Fujitsu MAS3184NC - Enterprise 18.4 GB Hard Drive Page 55 Product/Maintenance Manual Download

Page: 55 / 130

C141-E185

4-5

Impact caused by the electric driver must be within the device specifications.

Must be handled on an anti-static mat.

Figure 4.4

Mounting frame structure

(2)

Limitation of side-mounting

Mount the IDD using the 4 screw holes at the both ends on the both sides as shown in Figure 4.5.
Do not use the center hole by itself.

In case of using the center hole, it must be used in combination with 2 holes on both ends.
(Total 6 screws for 6 holes enclosed)

Use four holes (No.1-4) to mount.

Holes for
mounting screw.

Do not use these holes.

Holes for mounting screw

Figure 4.5

Limitation of side-mounting

5.0 or less

Summary of Contents for MAS3184NC - Enterprise 18.4 GB Hard Drive



































































































































Search results

Summary of Contents for MAS3184NC - Enterprise 18.4 GB Hard Drive

Reviews:

Related manuals for MAS3184NC - Enterprise 18.4 GB Hard Drive

Brands by name

Popular brands

Fujitsu MAS3184NC - Enterprise 18.4 GB Hard Drive, Product/Maintenance Manual

Search results

Summary of Contents for MAS3184NC - Enterprise 18.4 GB Hard Drive

Reviews:

Related manuals for MAS3184NC - Enterprise 18.4 GB Hard Drive

Brands by name

Popular brands