Fujitsu MAS3184NC - Enterprise 18.4 GB Hard Drive Page 58 Product/Maintenance Manual Download | Manualshive

Page: 58 / 130

background image

4-8

C141-E185

4.2

Power Supply Requirements

(1)

Allowable input voltage and current

The power supply input voltage measured at the power supply connector pin of the IDD (receiving
end) must satisfy the requirement given in Subsection 2.1.3. (For other requirements, see Items (4)
and (5) below.)

(2)

Current waveform (reference)

Figure 4.8 shows the spin-up current waveform of +12 VDC.

MAS3735NC/NP

Current (500mA/div)

Time (2 sec/div)

MAS3184NC/NP

MAS3367NC/NP

Current (500mA/div)

Current (500mA/div)

Time (2 sec/div)

Time (2 sec/div)

Figure 4.8

Spin-up current waveform (+12 VDC)

(3)

Power on/off sequence

a) The order of the power on/off sequence of +5 VDC and +12 VDC, supplied to the IDD, does

not matter.

b) In a system which uses the terminating resistor power supply signal (TERMPWR) on the SCSI

bus, the requirements for +5 VDC given in Figure 4.9 must be satisfied between the IDD and
at least one of the SCSI devices supplying power to that signal.

Figure 4.9

Power on/off sequence (1)

«
...
56
57
58
59
60
...
»

Summary of Contents for MAS3184NC - Enterprise 18.4 GB Hard Drive



































































































































Reviews:

No comments

Related manuals for MAS3184NC - Enterprise 18.4 GB Hard Drive

Taylor-Wharton XL-65

Brand: Harsco Pages: 26

2.5” Solid State Drive

Brand: YearGoo Pages: 6

Brand: LaCie Pages: 22

RACK PRO MINI-SAS

Brand: OWC Pages: 12

Brand: Magnusson Pages: 18

Brand: WiebeTech Pages: 8

Brand: SAJ Pages: 42

Storage Library T24

Brand: Tandberg Data Pages: 6

Brand: Magnusson Pages: 24

5BIG THUNDERBOLT 2

Brand: LaCie Pages: 20

MiniStation HD-PFU2 Series

Brand: Buffalo Pages: 94

Brand: QNAP Pages: 55

Brand: Edsal Pages: 2

Brand: EditShare Pages: 112

seasons 57-003-014301-00

Brand: Classic Accessories Pages: 3

Brand: Clas Ohlson Pages: 4

Brand: Clas Ohlson Pages: 16

Brand: Clarke Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands