Fujitsu MAS3184NC - Enterprise 18.4 GB Hard Drive Page 102 Product/Maintenance Manual Download

Page: 102 / 130

6-6

C141-E185

CAUTION

Always ground yourself with a wrist strap connected to ground before
handling. ESD (Electrostatics Discharge) may cause the damage to the
device.

To prevent electrical damage to the disk drive, turn the power off before
connecting or disconnecting a cable, connector, or plug.

Do not remove a PCA.

Do not use a conductive cleaner to clean a disk drive assembly.

Ribbon cables are marked with a colored line. Connect the ribbon cable to a
cable connector with the colored wire connected to pin 1.

6.2.2

Maintenance requirements

(1)

Preventive maintenance

Preventive maintenance such as replacing air filters is not required.

CAUTION

Damage
Never open the disk enclosure in the field.
Opening the disk enclosure may cause an irreparable fault.

(2)

Service life

See "(3) Service life," in Section 2.1.5.

Summary of Contents for MAS3184NC - Enterprise 18.4 GB Hard Drive



































































































































Search results

Summary of Contents for MAS3184NC - Enterprise 18.4 GB Hard Drive

Reviews:

Related manuals for MAS3184NC - Enterprise 18.4 GB Hard Drive

Brands by name

Popular brands

Fujitsu MAS3184NC - Enterprise 18.4 GB Hard Drive, Product/Maintenance Manual

Search results

Summary of Contents for MAS3184NC - Enterprise 18.4 GB Hard Drive

Reviews:

Related manuals for MAS3184NC - Enterprise 18.4 GB Hard Drive

Brands by name

Popular brands