Fujitsu MAS3184NC - Enterprise 18.4 GB Hard Drive Page 110 Product/Maintenance Manual Download | Manualshive

Page: 110 / 130

background image

6-14

C141-E185

Table 6.2

System-level field troubleshooting

Item

Recommended work

DC power cable

Check that the power cable is correctly connected to the disk drive and
power supply unit.

Check that the DC voltage is within the specified range (±5%).

Check that the +5 VDC value (pins 3 and 4 of the power connector) is
4.75 to 5.25 VDC.

DC power level

Check that the +12 VDC supply (pins 1 and 2 of the power connector of
disk drive) is 11.4 to 12.6 VDC.

Make sure the maximum ripple peak-to-peak value of +5 VDC is within
250 mV and +12 VDC is within 250 mV.

Electrical noise

Make sure the high frequency noise (over 20 MHz) is less than 100 mVp-p.

Interface cable connection

Check that the SCSI interface cable is correctly connected between the disk
drive and controller.

Terminating resistors

For a daisy chain connection, check the terminating resistor on the last disk
drive only. For a star-burst connection, check that the terminating resistor
is correctly mounted on all disk drives.

Drive selection address

Check that the disk SCSI ID is set correctly.

Plug setup

Check that the jumpers on the PCA are set so that the disk drive and host
computer operate normally. See Section 5.3.

System cables

Check that all system cables are connected correctly.

System diagnostic test

When possible, execute the system level diagnostic routine as explained in
the host computer manual. This gives a detailed report of a possible fault.

Check the AC voltage from the power supply. Check the DC voltage level
at the power connector for the disk drive.

If the AC voltage level is abnormal or there is a lot of electrical noise,
notify the user of the error.

If the DC voltage level is unstable, replace the power supply unit.

Intermittent or nonfatal errors

If possible, replace the disk drive. If replacing the disk drive does not
eliminate the error, the removed disk drive is probably not faulty. To
continue error analysis, refer to the hardware and software manuals
supplied with the system.

«
...
108
109
110
111
112
...
»

Summary of Contents for MAS3184NC - Enterprise 18.4 GB Hard Drive



































































































































Reviews:

No comments

Related manuals for MAS3184NC - Enterprise 18.4 GB Hard Drive

Brand: Wolfcraft Pages: 96

My Passport Essential SE

Brand: Western Digital Pages: 2

Brand: Backyard Pages: 60

Brand: HOGYME Pages: 31

Brand: Whalen Pages: 9

Brand: Clarke Pages: 4

Brand: Clarke Pages: 12

Brand: G-Technology Pages: 13

Brand: G-Technology Pages: 13

Brand: Alpha ESS Pages: 58

Brand: Scotts Pages: 36

Brand: Promise Technology Pages: 318

Brand: Teac Pages: 2

Brand: Kobalt Pages: 15

WD1000FYPS - RE2-GP

Brand: Western Digital Pages: 2

Brand: Power Fist Pages: 2

Brand: FreeNAS Pages: 36

NXA STEEL 420-9006

Brand: Nexgrill Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands