manualshive.com logo in svg

Fujitsu General AOHG45KRTA, Service Manual, Page: 111 / 154

Share
Download
Fujitsu General AOHG45KRTA Service Manual Download Page 111

5-1. Defrost operation in heating operation stopped

If the outdoor unit is frosted when stopping the heating operation, it stops after performing the auto-
matic defrosting operation.
In this time, if the indoor unit operation lamp flashes slowly (6 sec on/2 sec off), the outdoor unit al-
low the heat exchanger to defrost, and then stop.

•

Triggering condition

When all of the following conditions are satisfied in heating operation

– Compressor operation integrating time: 30 minutes or more
– Compressor continuous operation time: 10 minutes or more
– Outdoor unit heat exchanger temperature: -4°C or less

•

Release condition

The defrost operation is released when either one of the conditions below is satisfied.

Outdoor unit heat exchanger temperature
(after 1 minute or later since compressor start)

12°C or more

Compressor operation time

15 minutes

5-1. Defrost operation in heating operation stopped

- (04-17) -

5. Defrost operation control

CONTROL AND

FUNCTIONS

CONTROL AND

FUNCTIONS

Summary of Contents for General AOHG45KRTA



























































































































































Reviews:

No comments