Fuji Xerox DocuPrint C2120 User Manual Download

Page: 135 / 206

7.1 Replacing Consumables

135

Pinch the gray lever on the right side of the
Fuser Unit and lower the lever toward you.

Grasp both sides of the Fuser Unit. Slightly
raise the right side while holding down the
left side, and slide out the Fuser Unit.

Take out the new Fuser Unit from the box.

Insert the protrusions of the new Fuser Unit
in the two slots of the printer.

Note

• Hold both side of the Fuser Unit with your hands.
• Make sure that the Fuser Unit is firmly set in the slots

and cannot be moved easily.

Push the Fuser Unit forward until the right
groove of the fuser snaps into place.

10. Return the belt unit to its original position.

Summary of Contents for DocuPrint C2120














































































































































































































Search results

Summary of Contents for DocuPrint C2120

Reviews:

Related manuals for DocuPrint C2120

Brands by name

Popular brands

Fuji Xerox DocuPrint C2120, User Manual

Search results

Summary of Contents for DocuPrint C2120

Reviews:

Related manuals for DocuPrint C2120

Brands by name

Popular brands