manualshive.com logo in svg

FRTek PrimAer 28, Operating Manual

Share
Download
FRTek PrimAer 28 Operating Manual Download Page 19

   

 

 

 

PRIVATE AND CONFIDENTIAL ©  2020 FRTEK CO., LTD. 

 

19

 

PrimAer 28GHz 

Operating Manual

 
 

Output Interface 

Optic 

2 Ports 

 

 

Figure 3.  DU Port Configuration. 

 

No 

Content 

①

 

Port that transmit/receives optic signal 

②

 

Port to monitor T-SYNC 

③

 

Port to monitor Downlink SISO Path RF signal 

④

 

Antenna port to transmit external signal from the Modem 

⑤

 

Port to monitor Downlink MIMO Path RF signal 

⑥

 

Port to monitor internal 10MHz Reference signal 

⑦

 

Port to connect WEB GUI 

⑧

 

Port to supply -53.3V power from the Rectifier 

⑨

 

Port to connect GUI (Connected when cover is open) 

⑩

 

Internal Antenna, transmit/receive RF wireless signal 

 

3.2 SU Figure and Configuration 

The SU consists of One enclosure with a mounting bracket enabling wall attachment. The SU receives 

optic signal from the DU through Fiber-Optic cable, converts into 28GHz RF signal and sends the 5G 

signal through the antenna. (Downlink) It also converts the 28GHz RF signal received from the UE into 

optic signal and sends to the DU through Fiber-Optic cable. (Uplink) 

When  cascading  there  is  the  SU_C  that  connects  between  the  DU  and  SU_E,  the  figure  and 

configuration is the same. 

Summary of Contents for PrimAer 28































































Reviews:

No comments

Brands by name

Popular brands

Load more brands