Frontier EGA/PY-3030D Operation Manual Download Page 71

Page: 71 / 83

6-11

Ver.1.36

6.2.5 List of recommended replacement parts

Pats listed below are consumable parts that are recommended to replace during maintenance work.

The replacement interval raries depending on the usage.

6.2.6 Periodic maintenance and inspection

We recommend that the pyrolyzer be overhauled and inspected every two years and that

hard-to-replace parts such as heater and thermal insulator be replaced for your stable and safety

operation of the product.

Device

Part name

Part No.

Replacement

cycle

Note

Pyrolyzer
(Furnace)

Quartz pyrolysis tube
A30

PY1-3018A

As needed



Replacement interval depends on type of

samples, amount used, and number of runs.



Can be heat-cleaned with torch flame.

Graphite Vespel ferrule

PY1-7911

As needed



Replace when pyrolysis tube M30 is replaced.

Needle set N

PY1-1274

As needed



Replacement recommended when pyrolysis

tube M30 is replaced.



Over tightening injector septum may clog

needle opening with septum debris.

ITF union N

PY1-3513

1 year



Standard accessory for EGA/PY-3030D

ITF union ASN

PY1-3533

1 year



Used when Auto-Shot sampler is used.

O-ring P-6W

PY1-2017

As needed



For sealing pyrolysis tube M30, 2 pcs used

Eco pickup

PY1-EP55F

1 year



Replacement not needed when Auto-Shot

Sampler is used all the time.

Septa for liquid

sampler, 20 pcs

PY1-2025

1 year



Inspection may only be needed if liquid sample

injection with micro syringe is not done.

O-ring P12

PY1-7811

1 year



For sampler base.

Inlet/outlet septum

PY1-2028

6 months



Used for carrier gas tube joints

Double-Shot
sampler

Cup chuck

PY1-1345

1 year



Worn-out chuck does not hold eco stick firmly.



Special tool required.

Overhaul

2 years



The product needs to be returned to F-Lab.

O-ring P-3

PY1-2112

6 months

Absorption trap tube

PY1-2216

3~6 months

O-ring P-5

PY1-7814

3~6 months



Replace when trap tube is replaced. 4 pcs

used.

Septum

Agilent
PY1-7301

As needed



Replace if leakage detected when pyrolyzer

interface or GC injector cools down.



Replace when pyrolyzer is removed from GC

injector.

Shimadzu
PY1-7304

Others

Other parts that GC

manufacturers
recommend

Summary of Contents for EGA/PY-3030D




















































































Search results

Summary of Contents for EGA/PY-3030D

Reviews:

Related manuals for EGA/PY-3030D

Brands by name

Popular brands

Frontier EGA/PY-3030D, Operation Manual

Search results

Summary of Contents for EGA/PY-3030D

Reviews:

Related manuals for EGA/PY-3030D

Brands by name

Popular brands