Frontier EGA/PY-3030D Operation Manual Download Page 12

Page: 12 / 83

1 - 3

Ver.1.36

1.2 FEATURES OF EGA/PY-3030D

The features of the EGA/PY-3030D pyrolyzer are summarized below:

1. Operational temperature range: a10ºC to 1,050ºC.

2. A low mass, high temperature ceramic heater rapidly heats and cools

3. Performance guaranteed in both the EGA and Single-Shot modes.

4. All wetted surfaces deactivated

5. Needle interface is heated using a specially designed adapter. This ensures thermo homogeneity

and greatly improves the analysis of high boiling compounds

6. Various types of sample analysis (four analytical methods and five samplers)

Choose an analytical method and a sampler based on your analytical purposes and sample matrix.

The standard operating software is used for:



Single-Shot GC



Double-Shot GC



Evolved gas analysis (EGA-MS)



Heart-Cut EGA-GC/MS

Five samplers



Double-Shot sampler (standard)



Liquid sampler (standard)



Online-micro reaction sampler (optional)



Micro thermal desorption sampler (optional)



Online micro UV sampler (optional)

Summary of Contents for EGA/PY-3030D




















































































Search results

Summary of Contents for EGA/PY-3030D

Reviews:

Related manuals for EGA/PY-3030D

Brands by name

Popular brands

Frontier EGA/PY-3030D, Operation Manual

Search results

Summary of Contents for EGA/PY-3030D

Reviews:

Related manuals for EGA/PY-3030D

Brands by name

Popular brands