Frontier EGA/PY-3030D Operation Manual Download Page 60

Page: 60 / 83

Ver.1.36

5-11

5.6 SELECTION OF SAMPLE CUPS AND STICKS

The types of Eco-cups and Eco-sticks are selected from Table 5.1 depending on your analytical

purpose and the technique that you use.

Eco-cups and Eco-sticks are made of stainless steel; the entire surface has been deactivated by

coating with fused silica on the surface. The wall thickness is 0.1 mm for all.

Type / Appearance

Name

Part Number

Volume

(µL

）

Compatibility
with AS-1020E

Description

Eco-cups

Regular L

Eco-cup LF

PY1-EC80F

(100 pcs)

Yes

For all applications except for Micro UV

Irradiator

(UV/Py-GC/MS).

Optimum

pyrolysis temperature is 30ºC lower than

Eco-cup SF for most polymeric materials

due to large surface area. This is useful for

samples with relatively large volumes.

Regular S

Eco-cup SF

PY1-EC50F

(100 pcs)

For all applications except for Micro UV

Irradiator

(UV/Py-GC/MS).

This

cup

provides

slightly

better

pyrogram

reproducibility in flash pyrolysis-GC mode

than Eco-cup LF.

Flow through

Eco-cup

LHF

PY1-EC80HF

(20 pcs)

This cup provides better peak shape

resolution of volatile compounds (C3-10)

than regular cups. And it prevents

secondary reactions under a low carrier

gas flow, e,g. 10mL/min.

Side hole

Eco-cup UV

PY1-EC80UV

Yes

Used for analysis with Micro UV Irradiator

(UV/Py-GC/MS)

Eco-sticks

Short

Eco-Stick SF

PY1-ES10F

(50 pcs)

---

Used for manual Single-Shot, EGA or

Heart-Cut EGA analysis.

Long

Eco-Stick DF

PY1-ES20F

(50 pcs)

---

Used for manual Double-Shot analysis.

Table. 5.1 Selection of sample cups and sticks

4mm

8mm

5mm

4mm

1mm i.d.
hole

8mm

4mm

1mm i.d.
hole x 2

8mm

4mm

L=30 mm

L=80 mm

Summary of Contents for EGA/PY-3030D




















































































Search results

Summary of Contents for EGA/PY-3030D

Reviews:

Brands by name

Popular brands

Frontier EGA/PY-3030D, Operation Manual

Search results

Summary of Contents for EGA/PY-3030D

Reviews:

Brands by name

Popular brands