Fröling TM 320-550 Installation Instructions Manual Download Page 76

Page: 76 / 96

5 | Assembly

M0691622_en | Installation instructions TM 320-550

5.5.30 Assembling the automatic ignition

Fit the igniter tube (A)

Place the double screw clip (B) onto the igniter tube (A)

Insert the ignition fan (C) into the igniter tube (A) and fix in place using the double
screw clip (B)

Fit the cover (D)

Fitting the automatic ignition to the slide-on duct (optional):

Remove the blanking plug

Insert the igniter tube (A)

Attach the double nipple (B), sleeve (C) and elbow (D) to the igniter tube (A)

Fit further double nipples (B) to the elbow (D)

Insert the fibreglass braid (E) and cap (F) into the ignition fan (G)

Insert the ignition fan (G) into the double nipple (B) and fix in place with the cap (F)

Summary of Contents for TM 320-550

































































































Search results

Summary of Contents for TM 320-550

Reviews:

Related manuals for TM 320-550

Brands by name

Popular brands

Fröling TM 320-550, Installation Instructions Manual

Search results

Summary of Contents for TM 320-550

Reviews:

Related manuals for TM 320-550

Brands by name

Popular brands