Frigidaire LGUB2642LF2 Service Manual Download Page 24

Page: 24 / 187

Electronic Control

3-2

Pro-Select

™

User Interface Display Operation

(Dispenser Models)

options

Touch an icon (Water/Cube/Crush) to activate the desired

dispenser mode.

light on-off

On / Off

control lock

Press and hold for three (3) seconds

to activate and deactivate. The

Lock icon will be displayed in the

LCD window. This restricts unde-

sired changes to the refrigerator’s

settings and prevents use of the ice

and water dispenser.

options

Touch to display options menu.

Use the menu buttons to scroll

down to either freezer or refrigera-

tor temp to adjust temperatures.

Use the Temp Adjust buttons to ad-

just the temperature to the desired

setting.

Press the SET button to accept the

new temperature setting.

Press options button to exit the

main menu.

IMPORTANT

Pressing the power off icon does not turn off power to

your refrigerator. You must unplug the power cord from

the wall outlet.

power on-off

Press and hold for three (3) seconds

to turn off the cooling system to

clean the refrigerator. It also turns

off all dispenser functions. The tem-

perature display will read “OF”.

Figure 3-4. Pro-Select™ User Interface for Dispenser Models

Summary of Contents for LGUB2642LF2




























































































































































































Search results

Summary of Contents for LGUB2642LF2

Reviews:

Related manuals for LGUB2642LF2

Brands by name

Popular brands

Frigidaire LGUB2642LF2, Service Manual

Search results

Summary of Contents for LGUB2642LF2

Reviews:

Related manuals for LGUB2642LF2

Brands by name

Popular brands