Frigidaire LGUB2642LF2 Service Manual Download Page 126 | Manualshive

Page: 126 / 187

background image

6-20

Component Teardown

Figure 6-60

Figure 6-61

4. To replace the tube, insert the green end into the
opening of the conduit inside the fresh food compart-
ment.
5. Push the tube through the conduit and out the back
of the unit.

IMPORTANT:

Be sure the black portion of the tube is

oriented as shown in figure 6-59, otherwise, the black
portion may kink when inserted into the conduit.
6. Push the black portion of the tube about halfway into
the conduit.
7. From the back of the unit, pull the green tube until
the black portion snaps into place. It is in position when
the flat disk is against the top of the liner.
8. Connect the green tube to ¼” green tube from the
water valve at the in-line connector.

Air Handler Removal

Disconnect power from the unit before performing this
procedure.

NOTE:

When the Air Handler assembly is removed, the

gaskets on the Evaporator Housing are compromised.
The rear-most gasket must always be replaced, and all
other Evaporator Housing gaskets must be evaluated and
replaced if deformed or damaged. This is essential to
ensure that any water collected within the ice maker air
handler assembly during normal operation is contained
and drains properly.
1. After completing the Ice Maker Housing Removal pro-
cedure, remove the three screws that hold the Air Handler
in place. Figure 6-60.

NOTE:

There are 4 screw holes in the Air Handler, but

only 3 are used – the 2 top holes and the bottom right
hole.
2. Carefully pull the Air Handler off of the Evaporator
Housing.
3. While holding the Air Handler in one hand, unplug the
internal wire harness with the other. Figure 6-61.

NOTE:

the Air Handler is heavier that you may expect

due to the Auger Motor that is mounted inside it. Be care-
ful that you do not drop it, as you may damage the wiring
harness or the glass shelf underneath the ice maker.

disconnect the

harness while

supporting

the air handler

assembly

remove 3 screws

«
...
124
125
126
127
128
...
»

Summary of Contents for LGUB2642LF2




























































































































































































Reviews:

No comments

Related manuals for LGUB2642LF2

Brand: NEFF Pages: 23

Brand: NEFF Pages: 24

Brand: NEFF Pages: 20

Brand: True Pages: 2

Millennium DAR452BL

Brand: Danby Pages: 30

accucold CT66BBI Series

Brand: Summit Pages: 12

Brand: V-ZUG Pages: 64

Brand: Continental Refrigerator Pages: 2

Brand: Rangemaster Pages: 20

Brand: POCO Line Pages: 54

Brand: NewAir Pages: 13

Brand: DAEWOO ELECTRONICS Pages: 20

Brand: NEFF Pages: 95

Brand: Smeg Pages: 26

Brand: Continental Refrigerator Pages: 2

Brand: Jenn-Air Pages: 21

Brand: YATO Pages: 90

Brand: Engel Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands