Frigidaire LGUB2642LF2 Service Manual Download Page 129 | Manualshive

Page: 129 / 187

background image

6-23

Component Teardown

Figure 6-68

Evaporator Housing Replacement

Disconnect power from the unit before performing this
procedure.

IMPORTANT:

When the Evaporator Housing is re-

moved, (and when the Air Handler is removed), the rear
“U” shaped gasket on the Evaporator Housing must be
replaced. This is because the gasket gets crushed during
installation and permanently takes on the shape of the
liner where it contacts the liner. Once the Evaporator
Housing is removed or loosened, it will never be put back
in exactly the same place and the gasket will not properly
seal – leading to the possibility of melted frost bypassing
the gasket and causing water droplets that run down the
back wall of the fresh food compartment underneath the
ice maker.
1. Check all the gaskets on the Evaporator Housing. Re-
place any that are deformed or damaged. The rear-most
“U” shaped gasket must be replaced. Figure 6-66.
2. When replacing the rear gasket, be sure that the edge
of the new gasket is aligned with the tips of the small
“wings” on either side of the Housing as shown. Figure
6-67.
3. Be sure the aluminum liner and the tape are in place,
and carefully slip the Housing onto the bottom of the
Evaporator and slide it upward.

Note:

Use care to make sure the Heater stays in the

proper position.
4. Push the Housing all the way to the top of the Evapo-
rator. It is in the proper position when the top of the
Evaporator coil is even with the bottom of the large
window in the Housing as shown. Figure 6-68.
5. Route the wires from the Heater and Thermostat as-
sembly down through the “L” shaped slot and to the left
of the “L” shaped post on the Evaporator Housing, and
snap the connector into the clip on the front of the hous-
ing from behind as shown. Figure 6-69.

IMPORTANT:

The wires must be routed as shown.

Failure to do so could cause damage to the wires due to
pinching and interference with the Auger Motor.

The “U” shaped gasket

on the back of the

evaporator housing

must be replaced when
the evaporator housing

is loosened or removed.

align here

Figure 6-66

Figure 6-67

Figure 6-69

evaporator coil

aligned with

this edge of the

housing

“L” shaped post

“L” shaped slot

«
...
127
128
129
130
131
...
»

Summary of Contents for LGUB2642LF2




























































































































































































Reviews:

No comments

Related manuals for LGUB2642LF2

Brand: Amica Pages: 100

Brand: Heinner Pages: 60

Brand: Caple Pages: 9

Brand: Indel B Pages: 137

Brand: Küppersbusch Pages: 60

Brand: Fisher & Paykel Pages: 63

Brand: Omcan Pages: 16

Brand: Maytag Pages: 1

Brand: Rangemaster Pages: 20

Brand: Philco Pages: 156

Brand: Westinghouse Pages: 11

Brand: VOX electronics Pages: 118

Brand: barkman Pages: 6

Brand: Dometic Pages: 36

Brand: Scandomestic Pages: 13

Brand: Flavel Pages: 12

Brand: Caple Pages: 24

GE Profile Energy Star PSS23SGS

Brand: GE Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands