Frigidaire LGUB2642LF2 Service Manual Download Page 163

Page: 163 / 187

7-19

Sealed System

Figure 7-14.

Figure 7-15. Dye Drier Kit

Cut

Here

Cut

Here

Liquid Line

To Freezer

To Icemaker

Figure 7-16. Two Stage Drier Kit

DO NOT unbraze old filter-drier from system. This
will vaporize and drive moisture from desiccant
back into system. The old filter-drier should be cut
out of system.

4. Using a 3 cornered file, score a groove around

capillary tubes as close to old filter-drier as possible.
Break capillary tubes along score mark from filter-
drier.

5. Cut condenser outlet tube at filter-drier. Discard
filter-drier.

6. Thoroughly clean condenser outlet tube and
capillary

tube.

7. Place inlet connection of filter-drier over condenser

tube approximately ¼” and solder.

8. Insert capillary tubes input end into filter-drier

outlets. (See Figure 7-12,13 and 14) Do not allow
tube to bottom against screen. Solder carefully so
that solder does not plug capillary tube.

9. Install process tube adapter to filter-drier.

10. Evacuate and charge system using recommended

procedure described under Evacuating and
Recharging.

11. Reassemble unit.

Capillary Tube

Cut

Her e

Cut

Her e

Figure 7-17

Summary of Contents for LGUB2642LF2




























































































































































































Search results

Summary of Contents for LGUB2642LF2

Reviews:

Related manuals for LGUB2642LF2

Brands by name

Popular brands

Frigidaire LGUB2642LF2, Service Manual

Search results

Summary of Contents for LGUB2642LF2

Reviews:

Related manuals for LGUB2642LF2

Brands by name

Popular brands