Friendly Robotics Robomow RL1000 Operating & Safety Manual Download Page 6

Page: 6 / 73

25. Never raise the mower or attempt to inspect the blades while the mower is operating.

26. Always remove the power pack before lifting the mower or attempting any adjustments.

27. Do not start Robomow



operation in automatic mode outside the plot bounded by the

perimeter wire.

Docking Station

28. When programming the automatic departure times and days, insure these windows of

operation are programmed when children, pets and other bystanders are not on the lawn.

29. Do not use the Docking Station power supply with an extension cord.

30. Do not place metal objects in the area of the charging contacts on the Docking Station.

31. Do not place metal objects across the charging pins of the Robomow.

32. After removing the power pack from the mower always reset the current day and time.

Failure to do so may result in improper setting of the day and time and non-intentional

operation of the Robomow, which may cause sever bodily injuries.

33. Do not spray water directly into the docking area of the Docking Station or onto the

operating panel of the Docking Station.

Maintenance and storage

34. Maintain, service, and store Robomow



according to the instructions (refer to chapter 9).

35. Keep all nuts, bolts, and screws tight to assure safe condition of this appliance.

36. Replace worn or damaged parts for safety.

37. Use heavy gloves when inspecting or servicing the blades.

38. Use only the original equipment, power pack and power supply/charger with this mower.

Incorrect use may result in electric shock, overheating or leakage of corrosive liquid from

the battery.

39. The charger (power supply) is for indoor use only. Do not use in areas where moisture or

water is likely. It is required placing it in a sheltered place, dry location, which is well

ventilated and not exposed to direct sunlight.

40. Do not dispose of the battery pack in a fire and do not place used batteries in your

household trash. The battery must be collected, recycled, or disposed of in an

environmentally sound manner.

41. Do not open or mutilate the power pack. Released electrolyte is corrosive and may damage

the eyes or skin.

42. Wear eye protection and use gloves when installing the perimeter wire and driving the wire

stakes/pegs. Firmly drive all pegs in order to keep the wire from becoming a tripping

hazard.

43. Do not use the power supply/charger if the cord has damaged.

44.

Transport - to safely move from or within the working area:

1. Use the Manual Controller to drive it from place to place (See section 2.4)

2. In case of different height level or stairs, remove the Power Pack from the mower and

carry the mower by the carrying handle (See Figure no. 2.1).

Summary of Contents for Robomow RL1000










































































Search results

Summary of Contents for Robomow RL1000

Reviews:

Related manuals for Robomow RL1000

Brands by name

Popular brands

Friendly Robotics Robomow RL1000, Operating & Safety Manual

Search results

Summary of Contents for Robomow RL1000

Reviews:

Related manuals for Robomow RL1000

Brands by name

Popular brands