manualshive.com logo in svg

Friendly Robotics Robomow RL1000, Operating & Safety Manual, Page: 32 / 73

Share
Download
Friendly Robotics Robomow RL1000 Operating & Safety Manual Download Page 32

 

32 

Severe injury is possible.  Always remove the Power Pack when attempting 

to adjust the height of cut or otherwise lifting the mower off the ground.  

Never lift the mower or attempt to adjust the cutting height during 

operation.  Blades are very sharp and severe cuts or lacerations 

 

are possible.  When working around or near the blades 

 

always wear heavy gloves.

 

!

WARNING!

 

2.5  Setting The Cutting Height And Ground Clearance 
 

Remove the Power Pack before making any adjustments. The Robomow has two basic adjustments, 
cutting height and ground clearance.  When using the high cut blades, the cutting height is adjustable 
from approximately 1.5 inches to 3.5 inches (3.8 cm – 8.9 cm) and with the low cut blades from 1 inch 
to 2.5 inches (2.5 cm – 6.4 cm). By using the small wheels the minimum cutting height received is 
0.75 inches (20 mm)

. 

The ground clearance has two adjustment positions. The cutting height 

adjustment is located at the front wheel and is controlled by rotating the front wheel hub in or out, 
which effectively causes the front wheel to be raised or lowered.  See Figure 2.7.  

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 

 

The ground height adjustment is located in the Power Pack compartment of the mower.  See Figure 
2.8.  It has two positions, upper and lower. 

(The small wheels have three; upper, lower and middle)

 

The lower position (closest to the bottom of the Power Pack compartment) provides the highest level 
of ground clearance while the upper position (farthest from the bottom of the Power Pack 
compartment) provides the lowest level of ground clearance.  See Figure 2.9. It is typically 
recommended to adjust the rear ground clearance for maximum clearance, which is the setting 
closest to the base of the Power Pack compartment.  European lawns and lawns where the grass is 
cut at extremely low levels of less than 2.0 inches (5 cm) may find that adjusting the ground clearance 
to the minimum level may work best for them. 

 
 

 
 
 
 
 
 
 
 
 
 
 
 

Figure 2.7 – Adjusting the Height of Cut

Figure 2.8 – Ground Clearance Location

 

Figure 2.9 – Adjusting Ground Clearance

Rear ground height 
adjustment is located 
in the Power Pack 
compartment

. 

To adjust ground 
clearance, pull out 
on tab as shown 
and slide tab up or 
down. 

Rotate the front wheel 

hub in (lower) or out 

(higher) to adjust the 

cutting height.  Each 

click represents about 

1/4 inch (6 mm) in 

 

height of cut.

 

Rotate this 

direction for lower 

cut 

Rotate this 

direction for higher 

cut 

Summary of Contents for Robomow RL1000










































































Reviews:

No comments