background image

3

920-159-02

Vert-I-Pak Installation Recommendations

For proper unit performance and maximum operating life please refer to the minimum installation clearances below.

The above suggestions are for reference only and do not represent all possible installations. Please contact the factory 
for information regarding affects of other installation arrangements. 

By following these simple recommendations you can be confi dent that your Friedrich Vert-I-Pak

®

 will provide years 

of worry-free operation.

Fig ure  2

Fig ure  1

Any time obstructions are present use 
the following guidelines for proper 
spacing from the VERT-I-PAK louver: 

•  For minor obstructions such as lamp 

poles or small shrubbery a clearance 
of 24" from the outdoor louver should 
be maintained. 

•  For major obstructions such as a solid 

fence, wall or other heat rejecting 
device like a condensing unit, a mini-
mum distance of 72" should be kept.

12"

24"

60"

VPAK

VPAK

VPAK

POLE

FENCE

MAJOR OBSTRUCTION

BUILDING

OUTDOOR
CONDENSING

UNIT

72"

24"

SHRUB

VERT-I-PAK

®

 units must be installed on an outside wall. Confi ned spaces and/or covered areas should be 

avoided. Units should be installed no closer than 12" apart when two units are side by side. If three of more 
units are to operate next to one another allow a minimum of 60" between units or pairs of units. Also, a vertical 
clearance of 60" should be maintained between units. Units installed on the bottom fl oor should be mounted 
at least 6" off of the ground. 

A

B

60"

60"

60"

60"

LARGER RECESS OK. IF A> 5xB

12"

6"

60"

60"

60"

6"

60"

60"

6"

60"

60"

SMALL RECESS OK

Summary of Contents for Vert-I-Pak VEA24 Series

















Reviews: