manualshive.com logo in svg

Fri-Jado Deli Multisserie, Service Manual

Share
Download
Fri-Jado Deli Multisserie Service Manual Download Page 20

13

13

13

13

13

13

V5_00_13.bin

PROGRAMMING INSTRUCTIONS

Page 20

Service  Manual Deli Multisserie   form 9123667  rev. 20220317

Since software version V5.02.07 it is possible to load and save files on a USB stick

The possibilities are:

 

 

-Load and save cook book

 

 

-Load and save parameter file

 

 

-Save Error history

 

 

-Save HACCP log

All cook books (also called recipes or programs) that are saved come automaticly in a folder 

named “PROGRAMS”, which is placed in the root of the USB stick.

All (external) cook books that need to be loaded into the unit, need to be placed in the same 

“PROGRAMS” folder.

Saving and loading cookbooks has to be done in the Manager menu.

Saving and loading parameters and saving error history or haccp logs has to be done in the   

Service menu.

For parameters, the folder “PARAMS” is used.

For  error history and HACCP log, the folder “LOG” is used.

SAVING AND LOADING FILES

Updating systemsoftware (firmware).

 Only if needed!!

This software, supplied by Fri-Jado comes in a “zip” file with the version number of the soft-
ware, for example “V5_00_13.zip”. The file needs to be copied on a USB stick. (disk “STORE N 
GO (F:)” in the example)
After unpacking it, the folder named “42-I+CPU” needs to be moved or copied to the root of 
the USB stick as shown below.

==> Untill software version V5.xx.xx can be used on all boards (with USB port)
==> For software version V6.xx.xx, bootloader version 1.02.02 or higher, is necessary.

Now proceed as follows:
1.  Switch OFF the mains supply or pull the mains plug.
2.  Connect the usb stick. 
3.  Switch the power back on or put the mains plug back in. You will see that the controller 

detects the software and starts uploading

4.  You will be asked to remove the stick and when done the unit switches off. ( the existing 

parameters will remain).

5.  In case the board has just been put into a unit, it has to be set to the right device 

type!!!!!

 This has to be done in the service menu. Refer to the previous page.

After unpacking

Move the “42-I+CPU” folder to the root.

Summary of Contents for Deli Multisserie





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands