manualshive.com logo in svg

Fresenius Kabi OPTIMA PT-VS-S, Technical Manual

Share
Download
Fresenius Kabi OPTIMA PT-VS-S Technical Manual Download Page 63

optima06.0_0020b_en.fm

63

Inte

rv

en

tio

n

 pr

o

c

ed

ur

es

Re-assembling

Each Optima pump has its own type of "display and CPU board"; it is important that you 
do not mix up the different Optima pump references and that you order the one that 
corresponds to your device. 

Carry out the dismantling procedure in reverse order to re-assemble the new unit.

When fixing the display board, ensure that the plastic inserts are not tightened too much 
or they will be damaged. 
When positioning the front case, ensure that the sealing is perfectly positioned in its 
housing after re-assembling.

When closing the pump, ensure that the 2 cables connecting the power supply board 
and the CPU board are positioned above the motor. Also check that the earth wire is 
next to the metal support.
Incorrect positioning of one of these cables could result in a noise being heard when 
the pump is in operation. (See photo on procedure sheet n°1.)

!

Carry out regular servicing checks. (See Quality Control Certificate.)

Summary of Contents for OPTIMA PT-VS-S











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands