Fresenius Kabi OPTIMA PT-VS-S Technical Manual Download Page 50

Page: 50 / 106

optima05.1_001a_en.fm

roub

les

Battery alarm while
it has been
completely charged

Battery is totally

discharged

Check the charging voltage

Replace the battery

Battery alarm
whereas the
Optima is
connected to the
mains

Power supply or CPU

boards are faulty

Check the charging voltage

Check the power supply mains fuses

Replace the power supply if

necessary.

If the problem remains, replace the

CPU board and carry on a complete
configuration

The module MVP
turns ON or turns
OFF alone

Keyboard is defective

CPU board is

defective

Check the keyboard ( test 3)

Replace the keyboard if necessary

Check that there was no liquid

infiltration on the CPU board

Replace the CPU board and carry

on a complete configuration of the
device

Some keys from
keyboard out of
order

Keyboard is defective

Check the keyboard (test 3)

Replace the keyboard if necessary

After a fall

Mechanical elements

damaged

Check that the mechanical

assembly and the cases are intact

Pump noisy

Power supply and

CPU wires are closed to
the motor (earth wire
also)

Fix the wires as it shown on the

technical manual

Problems

Causes

Action

Summary of Contents for OPTIMA PT-VS-S











































































































Search results

Summary of Contents for OPTIMA PT-VS-S

Reviews:

Brands by name

Popular brands

Fresenius Kabi OPTIMA PT-VS-S, Technical Manual

Search results

Summary of Contents for OPTIMA PT-VS-S

Reviews:

Brands by name

Popular brands