background image

3

TROUBLESHOOTING

PROBLEM

PROBABLE CAUSES

CORRECTIVE ACTION

Pump does not turn on.

Pump not plugged in.

Plug in pump.

Circuit breaker shut off or fuse removed.

Turn on circuit breaker or replace fuse.

Accumulation of trash on float.

Clean float.

Float obstruction.

Check float path and provide clearance.

Defective switch.

Have pump serviced by authorized service center.

Defective motor.

Have pump serviced by authorized service center.

Pump will not shut off.

Float or float rod obstruction.

Check float and float rod path and provide clearance.

Pump is air locked.

Shut power off for approximately 1 minute, then restart. Repeat several times to clear air 
from pump.

Liquid inflow matches pump capacity.

Larger pump required.

Defective switch.

Disconnect switch, check w/ohmmeter, Open-infinitive resistance, closed-zero.

Pump runs but does not 
discharge liquid.

Check valve installed backwards.

Check flow indicating arrow on check valve body to ensure it is installed properly.

Check valve stuck or plugged.

Remove check valve and inspect for proper operation.

Lift too high for pump.

Check rating table.

Inlet to impeller plugged.

Pull pump and clean.

Pump is air locked.

(See corrective action above.)

Pump does not deliver 
rated capacity.

Lift too high for pump.

Check rated pump performance.

Low voltage, speed too slow.

Check for proper supply voltage to make certain it corresponds to nameplate voltage.

Impeller or discharge pipe is clogged.

Pull pump and clean. Check pipe for scale or corrosion.

Impeller wear due to abrasives.

Replace worn impeller.

Pump cycles continually.

No check valve in long discharge pipe 
allowing liquid to drain back into basin.

Install a check valve in discharge line.

Check valve leaking.

Inspect check valve for correct operation.

Basin too small for inflow.

Install larger basin.

REPLACEMENT PARTS LIST

ITEM 

NO.

PART NO.

DESCRIPTION

CATALOG NO./ 

MODEL NO.

511610 

                        

HT-10EN-CIM

511710 

                         

HT-10EN-CIA-FS                         

1

109440202 Screen Base

2

109460

Gasket, Screen Base

3

909023

Screw/Washer, 10-24 x 7/8"

5

5

4

950481

Capacitor, 10MFD, 370V

5

950482

Capacitor Bracket

6

928008

Seal Ring, 4.718 ID x .078 Wall

7

901203

Screw, Machine, #6-32 x 1/4"

8

909022

Screw/Washer, 10-24 x 5/8"

4

4

9

950227

Switch Assy, Non Mercury,Automatic

10

951660

Wire Harness Assy, Automatic

 

10

951661

Wire Harness Assy, Manual

11

927427

Loop Clamp, Black

 

12

901424

Screw, Machine, #8-32 x 1/2"

13**

951798

Lead Wire Assembly,White

14**

951799

Lead Wire Assembly,Red

15**

950502

Capacitor Insulating Boot

16**

950400

Closed End Connector

** Items not shown

Summary of Contents for LittleGIANT HT-10EN-CIA-FS













Reviews: