background image

Hampton® H15U-NG/LP Direct Vent Freestanding Gas Stove

11

installation

Important Message  

SAVE THESE INSTRUCTIONS

The    Direct  Vent  Freestanding  Gas  Stove  must 
be installed in accordance with these instructions. 
Carefully read all the instructions in this manual first. 
Consult  the  building  authority  having  jurisdiction 
to determine the need for a permit prior to starting 
the installation.

Note:  Failure to follow the instructions could 

cause a malfunction of the heater which 

could result in death, serious bodily in

-

jury, and/or property damage.  Failure to 

follow these instructions may also void 

your fire insurance and/or warranty.

Note: These instructions take precedence over 

Simpson Dura-Vent instructions.

Specifications

Fuels: 

H15U-NG is approved for use with natural 
gas.

 

H15U-LP is approved for use with lique-
fied petroleum gases (propane).

Electrical:

  120V  A.C. system.

Optional Circulation Fan: 

 

 

Variable speed, 125/75.

Log Sets: 

 Ceramic fibre, 4 per set.

Vent System:

 Coaxial (6-5/8" outer / 4" inner liner) 

rigid flue and termination cap.

Mobile / Manufactured Homes 
After First Sale

This Hampton

®

 product has been tested and listed 

by  ITS Testing  Services  as  a  Direct Vent  Room 
Heater to ANSI Z21.88.

This Direct Vent System Appliance must be installed 
in accordance with the manufacturer's installation 
instructions and the Manufactured Home Construc-
tion and Safety Standard, Title 24 CFR, Part 3280, 
or  the  current  Standard  of  Fire  Safety  Criteria 
for  Manufactured  Home  Installations,  Sites,  and 
Communities  ANSI/NFPA  501A,  and  with  CAN/
CSA Z240-MH Mobile Home Standard in Canada.

This  appliance  installation  must  comply  with  the 
manufacturer's  installation  instructions  and  local 
codes, if any. In the absence of local codes follow 
the current National Fuel Gas Code, ANSI Z223.1 
and the current National Electrical Code ANSI/NFPA 
70 in the U.S.A., and the current CAN/CGA B149 
Gas Installation Code and the current Canadian 
Electrical Code CSA C22.1 in Canada.

Before You  Start

Safe  installation  and  operation  of  this  appliance 
requires common sense, however, we are required 
by the Canadian Safety Standards and ANSI Stand-
ards to make you aware of the following:

CLOTHING OR OTHER FLAMMABLE 
MATERIAL SHOULD NOT BE PLACED 
ON OR NEAR THE APPLIANCE.

   

INSTALLATION AND REPAIR SHOULD 
BE DONE BY AN AUTHORIZED 
SERVICE PERSON. THE APPLIANCE 
SHOULD BE INSPECTED BEFORE 
USE AND AT LEAST ANNUALLY BY A 
PROFESSIONAL SERVICE PERSON. 
MORE FREQUENT CLEANING MAY 
BE REQUIRED DUE TO EXCESSIVE 
LINT FROM CARPETING, BEDDING 
MATERIAL, ETC. IT IS IMPERATIVE THAT 
CONTROL COMPARTMENTS, BURNERS 
AND CIRCULATING AIR PASSAGEWAYS 
OF THE APPLIANCE BE KEPT CLEAN.

DUE TO HIGH TEMPERATURES, THE 
APPLIANCE SHOULD BE LOCATED 
OUT OF TRAFFIC AND AWAY FROM 
FURNITURE AND DRAPERIES.

WARNING: FAILURE TO INSTALL THIS 
APPLIANCE CORRECTLY WILL VOID 
YOUR WARRANTY AND MAY CAUSE A 
SERIOUS HOUSE FIRE.

YOUNG CHILDREN SHOULD BE CARE-
FULLY  SUPERVISED WHEN THEY ARE 
IN THE SAME AREA AS THE APPLI-
ANCE.  TODDLERS, YOUNG CHILDREN 
AND OTHERS MAY BE SUSCEPTIBLE 
TO ACCIDENTAL CONTACT BURNS.  A 
PHYSICAL BARRIERS IS RECOMMEND-
ED IF THERE ARE AT RISK INDIVIDUAL 
IN THE HOUSE.  TO RESTRICT ACCESS 
TO A FIREPLACE OR STOVE, INSTALL 
AN ADJUSTABLE SAFETY GATE TO 
KEEP TODDLERS, YOUNG  CHILDREN 
AND OTHER AT RISK INDIVIDUALS OUT 
OF THE ROOM AND AWAY FROM HOT 
SURFACES. 

CHILDREN AND ADULTS SHOULD BE 
ALERTED TO THE HAZARDS OF HIGH 
SURFACE TEMPERATURES,  ESPE-
CIALLY THE FIREPLACE GLASS, AND 
SHOULD STAY AWAY TO AVOID BURNS 
OR CLOTHING IGNITION.  

This Hampton

®

 Mobile/Manufactured Home 

Listed  appliance  comes  factory  equipped 
with a means to secure the unit.

This Hampton

®

 Mobile/Manufactured Home 

listed  appliance  comes  equipped  with  a 
dedicated  #8  ground  lug  to  which  an  18 
gauge copper wire from the steel chassis 
ground must be attached.

This appliance may only be installed 
in an aftermarket permanently located, 
manufactured (USA only) or mobile home, 
where not prohibited by local codes.
 
This appliance is only for use with the type 
of gas indicated on the rating plate. This 
appliance is not convertible for use with 
other gases, unless a certified kit is used.

Summary of Contents for Hampton H15U-LP

























































Reviews: