background image

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD.  6988 Venture St., Delta, BC  Canada, V4G 1H4

920-425

MODELS:      H15U-NG Natural Gas       H15U-LP Propane   

02.18.22

H15U-NG/LP Direct Vent Gas Fireplace

Owners & 

Installation Manual

WARNING:  
If the information in these instructions are not 
followed exactly, a fire or explosion may result 
causing property damage, personal injury or loss 
of life. 

FOR YOUR  SAFETY
Do not store or use gasoline or other flammable 
vapours and liquids in the vicinity of this or any 
other appliance.

Installation and service must be performed by 
a qualified installer, service agency or the gas 
supplier.

FOR YOUR  SAFETY
What to do if you smell gas:
•  Do not try to light any appliance.
•  Do not touch any electrical switch. 

Do not use any phone in your 
building.

•  Immediately call your gas supplier 

from a neighbour's phone. Follow 
the gas supplier's instructions.

•  If you cannot reach your gas 

supplier, call the fire department.

This appliance may only be 
installed in an aftermarket 
p e r m a n e n t l y   l o c a t e d , 
manufactured (USA only) 
or mobile home, where not 
prohibited by local codes.
 
This appliance is only for use 
with the type of gas indicated 
on the rating plate. This 
appliance is not convertible for 
use with other gases, unless 
a certified kit is used.

Tested by:

Installer: Please complete the details on the back cover and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.

www.hampton-fire.com

Summary of Contents for Hampton H15U-LP

























































Reviews: