formlabs Fuse Sift Manual Download

Page: 12 / 50

2.3

Product components

2.3.1

Fuse Sift

Hood

: Prevents powder and debris from leaving the Fuse Sift’s workspace.

Vent

: Collects pluming powder.

Vacuum

: For cleaning the Fuse 1 and Fuse Sift after use.

Tool shelf

: Storage for break-out tools and brushes.

Build chamber port

: Access port for cooled cake to enter workspace.

Surface grate

: Protective grate covering the sifter.

Fresh powder hopper lid

: Access point for filling the fresh powder hopper.

Control panel

: A touchscreen and physical controls for interfacing with the Fuse Sift.

Build chamber latch

: Secures the build chamber.

Build chamber enclosure

: Area for housing the build chamber with prints ready to be

ejected. The powder catch at the bottom of the build chamber enclosure is a removable
tray for catching loose powder.

Powder catch

: Removable tray for catching loose powder.

Build chamber socket

: For the build chamber’s plug.

Mixer

: For mixing powder cartridges after filling.

Cartridge drawer

: For storing and filling a powder cartridge.

2
3
4
5
6
7
8
9

1 1

12
13
14

Summary of Contents for Fuse Sift



















































Search results

Summary of Contents for Fuse Sift

Reviews:

Related manuals for Fuse Sift

Brands by name

Popular brands

formlabs Fuse Sift, Manual

Search results

Summary of Contents for Fuse Sift

Reviews:

Related manuals for Fuse Sift

Brands by name

Popular brands