formlabs Fuse Sift Manual Download

Page: 11 / 50

Introduction |

2.2

Technical specifications

Parameter

Unit

Powder recovery station

Fuse Sift

3D printing technology

Selective Laser Sintering (SLS)

Minimum dimensions for convenient

access (W × D × H)

221.1 × 122.0 × 218.0 cm | 87.1 × 48.0 × 85.8 in

Powder recovery station dimensions

(W × D × H)

99.1 × 61.0 × 157.0 cm (188.8 cm with hood open)

39.0 × 24.0 × 61.8 in (74.3 in with hood open)

Powder recovery station weight

93 kg | 205 lb (without build chamber or powder)

Build chamber dimensions (W × D × H)

27.9 × 34.2 × 48.9 cm | 11.0 × 13.5 × 19.3 in

Build chamber weight

11 kg (17.6 kg, full with 20% packed powder)

24.3 lb (38.8 lb, full with 20% packed powder)

Build volume (W × D × H)

16.5 x 16.5 x 30.0 cm | 6.5 × 6.5 × 11.8 in (with radiused corners)

Material refresh rate

Print with up to 70% recycled powder

Hopper capacity, fresh powder

10.7 kg PA12 nylon | 23.6 lb PA12 nylon

Hopper capacity, used powder

9.8 kg PA12 nylon | 21.6 lb PA12 nylon

Operating environment

18–28 ºC | 68–81 ºF

Air handling

Negatively pressurized hood with replaceable HEPA filter

Power requirements

With a vacuum that draws less than 6 A (230 VAC)/12 A (120

VAC):

EU: 230 VAC, 7.5 A (dedicated circuit)

US: 120 VAC, 15 A (dedicated circuit)

With a vacuum that draws more than 6 A (230 VAC)/12 A (120

VAC):

EU: 230 VAC, 10 A (dedicated circuit)

US: 120 VAC, 20 A (dedicated circuit)

Vacuum requirements

Auxiliary vacuum that is grounded and bonded (e.g., a Class II,

Division 2 vacuum)

Connectivity

Wi-Fi: 2.4 GHz

Ethernet: 1000 Mbit

USB: 2.0

Wi-Fi connectivity

Protocol: IEEE 802.11 b/g/n

Frequency: 2.4 GHz

Supported security: WPA/WPA2

Ethernet connectivity

RJ-45 Ethernet (10BASE-T/100BASE-TX/1000BASE-T) LAN

port

Connect with a shielded Ethernet cable (not included):

minimum Cat5, or Cat5e or Cat6 for 1000BASE-T.

USB connectivity

USB (rev 2.0) B port with a USB A-B cable

Sound emission

Does not exceed 84 dB(A).

Powder recovery station control

Interactive touchscreen, physical buttons

Cartridge filling system

Automated

Alerts

Touchscreen alerts

Summary of Contents for Fuse Sift



















































Search results

Summary of Contents for Fuse Sift

Reviews:

Related manuals for Fuse Sift

Brands by name

Popular brands

formlabs Fuse Sift, Manual

Search results

Summary of Contents for Fuse Sift

Reviews:

Related manuals for Fuse Sift

Brands by name

Popular brands