Ford 2009 Edge Owner'S Manual Download

Page: 216 / 325

All Wheel Drive (AWD) vehicles:

Tow your All Wheel Drive vehicle with all four wheels on the ground or
with all four wheels off the ground using a vehicle transport trailer.

not tow your All Wheel Drive vehicle with the front wheels off
the ground (by using a tow dolly) and the rear wheels on the
ground.

This will cause damage to your AWD system. If you are using a

vehicle transport trailer, follow the instruction specified by the
equipment provider.

Note:

If you tow your vehicle with all four wheels on the ground, follow

these instructions:

•

Tow only in the forward direction.

•

Release the parking brake.

•

Place the transmission shift lever in N (Neutral).

•

Place the ignition in the accessory position (refer to

Starting

in the

Driving

chapter).

•

Do not exceed 65 mph (105 km/h)

•

Start the engine and allow it to run for five minutes at the beginning
of each day and at each fuel stop.

Tires, Wheels and Loading

215

2009 Edge

(edg)

Owners Guide, 3rd Printing
USA

(fus)

Summary of Contents for 2009 Edge






































































































































































































































































































































Search results

Summary of Contents for 2009 Edge

Reviews:

Related manuals for 2009 Edge

Brands by name

Popular brands

Ford 2009 Edge, Owner'S Manual

Search results

Summary of Contents for 2009 Edge

Reviews:

Related manuals for 2009 Edge

Brands by name

Popular brands