manualshive.com logo in svg

Ford 2009 Edge, Owner'S Manual

Share
Download
Ford 2009 Edge Owner'S Manual Download Page 148

One-time disable

If at any time the driver/front passenger quickly buckles then unbuckles
the safety belt for that seating position, the Belt-Minder

威

is disabled for

the current ignition cycle. The Belt-Minder

威

feature will enable during

the same ignition cycle if the occupant buckles and remains buckled for
approximately 30 seconds. Confirmation is not given for the one time
disable.

Deactivating/activating the Belt-Minder

姞

feature

The driver and front passenger Belt-Minder

威

are

deactivated/activated independently. When deactivating/activating
one seating position, do not buckle the other position as this will
terminate the process.

Read Steps 1 - 4 thoroughly before proceeding with the
deactivation/activation programming procedure.

Note

: The driver and front passenger Belt-Minder

威

features must be

disabled/enabled separately. Both cannot be disable/enabled during the
same key cycle.

The driver and front passenger Belt-Minder

威

features can be

deactivated/activated by performing the following procedure:

Before following the procedure, make sure that:

•

The parking brake is set.

•

The gearshift is in P (Park).

•

The ignition is off.

•

The driver and front passenger safety belts are unbuckled.

WARNING:

While the design allows you to deactivate your

Belt-Minder

威

, this system is designed to improve your chances of

being safely belted and surviving an accident. We recommend you
leave the Belt-Minder

威

system activated for yourself and others who

may use the vehicle. To reduce the risk of injury, do not
deactivate/activate the Belt-Minder

威

feature while driving the vehicle.

Seating and Safety Restraints

147

2009 Edge

(edg)

Owners Guide, 3rd Printing
USA

(fus)

Summary of Contents for 2009 Edge






































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands