manualshive.com logo in svg

Ford 2009 Edge, Owner'S Manual

The Ford 2009 Edge Owner's Manual is a comprehensive guide that provides detailed information and instructions on operating and maintaining your vehicle. Easily downloadable for free at manualshive.com, this manual helps you understand the features and functions of your Ford 2009 Edge to ensure a smooth and enjoyable driving experience.

Share
Download
background image

WARNING:

When lifting a plastic-cased battery, excessive

pressure on the end walls could cause acid to flow through the

vent caps, resulting in personal injury and/or damage to the vehicle or
battery. Lift the battery with a battery carrier or with your hands on
opposite corners.

WARNING:

Keep batteries out of reach of children. Batteries

contain sulfuric acid. Avoid contact with skin, eyes or clothing.

Shield your eyes when working near the battery to protect against
possible splashing of acid solution. In case of acid contact with skin or
eyes, flush immediately with water for a minimum of 15 minutes and
get prompt medical attention. If acid is swallowed, call a physician
immediately.

WARNING:

Battery posts, terminals and related accessories

contain lead and lead compounds.

Wash hands after handling.

Because your vehicle’s engine is electronically controlled by a computer,
some control conditions are maintained by power from the battery. When
the battery is disconnected or a new battery is installed, the engine must
relearn its idle and fuel trim strategy for optimum driveability and
performance. To begin this process:

1. With the vehicle at a complete stop, set the parking brake.

2. Put the gearshift in P (Park), turn off all accessories and start the
engine.

3. Run the engine until it reaches normal operating temperature.

4. Allow the engine to idle for at least one minute.

5. Turn the A/C on and allow the engine to idle for at least one minute.

6. Release the parking brake. With your foot on the brake pedal and with
the A/C on, put the vehicle in D (Drive) and allow the engine to idle for
at least one minute.

7. Drive the vehicle to complete the relearning process.

•

The vehicle may need to be driven 10 miles (16 km) or more to
relearn the idle and fuel trim strategy.

•

If you do not allow the engine to relearn its idle trim, the idle
quality of your vehicle may be adversely affected until the idle
trim is eventually relearned.

Maintenance and Specifications

288

2009 Edge

(edg)

Owners Guide, 3rd Printing
USA

(fus)

Summary of Contents for 2009 Edge






































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Edge

OEM Audio Reference Series Manual preview
Reference Series
Brand: OEM Audio Pages: 29
Waeco MagicWatch MWE800 Installation And Operating Manual preview
MagicWatch MWE800
Brand: Waeco Pages: 212
Honda 2011 Civic Sedan Vehicle Instruction Card preview
2011 Civic Sedan
Brand: Honda Pages: 5
Suzuki 990E0-54P56-000 Installers And Users Instructions preview
990E0-54P56-000
Brand: Suzuki Pages: 12
Jeep GLADIATOR 2022 Owner'S Manual preview
GLADIATOR 2022
Brand: Jeep Pages: 380
Rago FABRICATION R2223TTUNDM Installation Manual preview
R2223TTUNDM
Brand: Rago FABRICATION Pages: 10
Big Mikes Performance Parts STO N SHO SNS 144 Installation Procedures Manual preview
STO N SHO SNS 144
Brand: Big Mikes Performance Parts Pages: 7
Lincoln MKZ 2018 Quick Reference Manual preview
MKZ 2018
Brand: Lincoln Pages: 10
Axxess AXDSPX-TY1 Installation Instructions Manual preview
AXDSPX-TY1
Brand: Axxess Pages: 16
Whispbar K723W Fitting Instructions Manual preview
K723W
Brand: Whispbar Pages: 77
Westin 28-0160 Instructions preview
28-0160
Brand: Westin Pages: 3
Ford 2002 F-250 Owner'S Manual preview
2002 F-250
Brand: Ford Pages: 264
Edelbrock 3824 Installation Instructions preview
3824
Brand: Edelbrock Pages: 2
Kargo Master 408TC Installation Manual preview
408TC
Brand: Kargo Master Pages: 14
Waeco MagicWatch MWE850 Installation And Operating Manual preview
MagicWatch MWE850
Brand: Waeco Pages: 200
Alpine IVE-W530 (French) Mode D'Emploi preview
IVE-W530
Brand: Alpine Pages: 70
Truma Mover smart M Operating Instructions Manual preview
Mover smart M
Brand: Truma Pages: 84
Dodge 2009 RAM TRUCK Owner'S Manual preview
2009 RAM TRUCK
Brand: Dodge Pages: 543

Brands by name

Popular brands

Load more brands