background image

7

Operating instructions - mobiSERVE  

 

GB

DANGER 

Risk of injury and material damage because of improper installation, elec-

tric current or contaminated media 
Risk of injury from stumbling or falling because of improperly laid 

power lines.
Moving the device with defective castors and/or defective accessories 

is forbidden! 
If the power cable is not used, this one must be disconnected from the 

mobiSERVE and kept in a safe place.
Never work on a pump that is running

Mount or remove attachments and accessories only when the pump is 
switched off.

For your own safety, disconnect the pump in addition from the power supply.

Do not pump contaminated fluids

Take special care to ensure that there are no contaminants in the fluid to 
be pumped.

Damaged attachments and accessories can lead to personal injury and 

material damage

Attachments and accessories must be checked for wear, splits or other 
damage throughout its period of use.

Damaged accessories and attachments must be replaced immediately.

With reference to the period of use, please note the details in ZH 1A45.4.2 
or DIN 20066 Part 5.3.2.

Escaping liquids can cause environmental harm
Comply with the stipulations of the German Water Resources Act (WHG) and 
of the Plant Regulations of the German federal states.

3.     Transport and in-house transport

 

All lifting and transport work may only be done by qualified and suitably instructed personnel. Only use 

the provided attachment points as well as approved lifting gear and slings to lift the mobiSERVE.
Use appropriate means to secure the mobiSERVE and the related individual parts on a means of  

transport / transport pallet.
It is not allowed to transport the urea conveying system with fitted urea dispensing container! 

Urea dispensing containers / urea cans must be transported separately. The manufacturer's transport 

provisions must be observed.

CAUTION

It is forbidden to transport the mobiSERVE with plugged-in power cord. 

For a transport of the battery, the poles must be protected by caps and 
insulating tape.

WARNING!

Castors/tyres are provided for in-house transports. When moving the 
device, check to ensure that all flaps and doors are properly closed and that 
the urea container is safely placed on the mobiSERVE and is secured against 
falling!

Summary of Contents for mobiSERVE

































Reviews: