background image

www.fmiproducts.com

125079-01F

3

Carbon Monoxide Poisoning:

 Early signs of carbon monoxide poisoning resemble the flu, 

with headaches, dizziness or nausea. If you have these signs, the fireplace may not be work

-

ing properly. 

Get fresh air at once! 

Have fireplace serviced. Some people are more affected 

by carbon monoxide than others. These include pregnant women, people with heart or lung 

disease or anemia, those under the influence of alcohol and those at high altitudes.

Natural and Propane/LP Gas:

 Natural and propane/LP gas are odorless. An odor-making 

agent is added to the gas. The odor helps you detect a gas leak. However, the odor added to 

the gas can fade. Gas may be present even though no odor exists.
Make certain you read and understand all warnings. Keep this manual for reference. It is your 

guide to safe and proper operation of this fireplace.

 WARNING: Any change to this fireplace or it’s controls can be 

dangerous. Do not modify this fireplace under any circumstances. 

Any parts removed for servicing must be replaced prior to operat

-

ing fireplace.

 WARNING: Do not use a blower insert, heat exchanger insert or 

other accessory not approved for use with this fireplace.

 WARNING: This appliance is only for use with the type of gas 

indicated on the rating plate. This appliance is not convertible for 

use with other gases unless a certified kit is used.

 WARNING: Do not allow fans to blow directly into the fireplace. 

Avoid any drafts that alter burner flame patterns.

Due to high temperatures, the appliance should be located out of 

traffic and away from furniture and draperies.

Do not place clothing or other flammable material on or near the 

appliance. Never place any objects on the appliance.

Do not use this fireplace to cook food or burn paper or other flam

-

mable material.

This fireplace reaches high temperatures. Keep children and adults 

away from hot surface to avoid burns or clothing ignition. Fireplace 

will  remain  hot  for  a  time  after  shutdown. Allow  surface  to  cool 

before touching.

SAFETY

Continued

Summary of Contents for DVF-36LT-D









































Reviews: