manualshive.com logo in svg

Fluke ScopeMeter 19 B Series, Service Manual

Share
Download
Fluke ScopeMeter 19 B Series Service Manual Download Page 49

 

Performance Verification

 

 

4.6 Scope Input A&B Tests

 

4

 

  

4-25 

Proceed as follows: 
1.

 

Connect the test tool to the calibrator as shown in Figure 4-16. 

 

al55sca.bmp 

Figure 4-16. Test Tool Input A to TV Signal Generator 

2.

 

Select the following test tool setup: 

•

 

Reset the test tool 

•

 

Press 

 , then press 

 to open the Trigger Options menu. 

•

 

Choose   

VIDEO on A...

 , then from the shown opened menu choose  

 

Polarity:   POSITIVE |   PAL 

(

 

or

   NTSC    PALplus    SECAM

 ) 

•

 

Press 

 to select  

ALL LINES

  

•

 

Press 

 to enable the arrow keys for selecting the video line number. 

•

 

Using 

 select line number: 

⇒

 

622 for PAL, PALplus, or SECAM 

⇒

 

525 for NTSC. 

•

 

Using 

 and 

 set the Input A sensitivity to 2 V/div (the actual probe setting 

is 10:1). 

•

 

Using 

 select the time base to 20 

μ

s/div. 

3.

 

Set the calibrator to mode video with amp100%.  Set format and  marker line 
number to : 

⇒

 

PAL 622 (even), for PAL and  PALplus 

⇒

 

SECAM 622 (even), for SECAM 

⇒

 

NTSC 262 even, for NTSC. 

4.

 

Observe the trace, and check to see if the test tool triggers on the negative pulse 
before the marker pulse (see Figure 17). 

Summary of Contents for ScopeMeter 19 B Series























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands