manualshive.com logo in svg

Fluke ScopeMeter 19 B Series, Service Manual

Share
Download
Fluke ScopeMeter 19 B Series Service Manual Download Page 25

  

4-1 

Chapter 4 

Performance Verification 

 Title 

Page 

4.1 Introduction..................................................................................................  4-3 

4.2 Equipment Required For Verification .........................................................  4-3 

4.3 General Instructions.....................................................................................  4-3 

4.4 Operating Instructions..................................................................................  4-4 

4.4.1 Resetting the test tool ...........................................................................  4-4 

4.4.2 Navigating through menu’s ..................................................................  4-4 

4.4.3 Creating Test Tool Setup1....................................................................  4-5 

4.5 Display and Backlight Test..........................................................................  4-5 

4.6 Scope Input A&B Tests ...............................................................................  4-7 

4.6.1 Input A&B Vertical Accuracy Test ......................................................  4-7 

4.6.2 Input A&B DC Voltage Accuracy Test................................................  4-9 

4.6.3 Input A&B AC Voltage Accuracy Test (LF) .......................................  4-11 

4.6.4 Input A & B AC Coupled Lower Frequency  Test...............................  4-12 

4.6.5 Input A and B  Peak Measurements Test..............................................  4-13 

4.6.6 Input A&B Frequency Measurement Accuracy Test ...........................  4-14 

4.6.7 Input A&B Phase Measurements Test..................................................  4-15 

4.6.8 Time Base Test .....................................................................................  4-16 

4.6.9 Input A Trigger Sensitivity Test...........................................................  4-17 

4.6.10 Input A AC Voltage Accuracy (HF) & Bandwidth Test ....................  4-19 

4.6.11 Input B Trigger Sensitivity Test .........................................................  4-20 

4.6.12 Input B AC Voltage Accuracy (HF) & Bandwidth Test ....................  4-21 

4.6.13 Video test using the Video Pattern Generator ....................................  4-22 

4.6.14 Video test using SC600 Scope Calibration Option ............................  4-24 

4.7 External Trigger Level Test .........................................................................  4-27 

4.8 Meter (DMM) Tests.....................................................................................  4-28 

4.8.1 Meter DC Voltage Accuracy Test ........................................................  4-28 

4.8.2  Meter AC Voltage Accuracy & Frequency Response Test .................  4-29 

4.8.3 Continuity Function Test......................................................................  4-30 

4.8.4 Diode Test Function Test .....................................................................  4-30 

4.8.5 Ohms Measurements Test ....................................................................  4-30 

4.9 Probe Calibration Generator Test ................................................................  4-32 

 

Summary of Contents for ScopeMeter 19 B Series























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands