manualshive.com logo in svg

Fluke ScopeMeter 19 B Series, Service Manual

Share
Download
Fluke ScopeMeter 19 B Series Service Manual Download Page 46

Fluke 19xB-19xC-2x5C 

Service Manual 

4-22 

4.6.13 Video test using the Video Pattern Generator 

You can skip this test if you do the test 

4.6.14 Video test using the SC600 Scope 

Calibration option

 

Only one of the systems NTSC, PAL, PALplus, or SECAM has to be verified. 
Proceed as follows: 
1.

 

Connect the test tool to the TV Signal Generator as shown in Figure 4-8. 

 

al-tv-a.bmp 

Figure 4-8. Test Tool Input A to TV Signal Generator 

2.

 

Select the following test tool setup: 

•

 

Reset the test tool 

•

 

Press 

 , then press 

 to open the Trigger Options menu. 

•

 

Choose   

VIDEO on A...

 , then from the shown opened menu choose  

 

Polarity:   POSITIVE |   PAL 

(

 

or

   NTSC    PALplus    SECAM

 ) 

•

 

Press 

 to select  

ALL LINES

  

•

 

Press 

 to enable the arrow keys for selecting the video line number. 

•

 

Using 

 select line number: 

⇒

 

622 for PAL, PALplus, or SECAM 

⇒

 

525 for NTSC. 

•

 

Using 

 and 

 set the Input A sensitivity to 2 V/div (the actual probe setting 

is 10:1). 

•

 

Using 

 select the time base to 20 

μ

s/div. 

3.

 

Set the TV Signal Generator to source a signal with the following properties: 

•

 

the system selected in step 2 

•

 

gray scale 

Summary of Contents for ScopeMeter 19 B Series























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands