manualshive.com logo in svg

Fluke ScopeMeter 19 B Series, Service Manual

Share
Download
Fluke ScopeMeter 19 B Series Service Manual Download Page 48

Fluke 19xB-19xC-2x5C 

Service Manual 

4-24 

 

al-tv-ai.bmp 

Figure 4-13. Test Tool Input A to TV Signal Generator Inverted 

8.

 

Select the following test tool setup: 

•

 

Press 

 to open the Trigger Options menu. 

•

 

Choose   

VIDEO on A...

 , then from the shown opened menu choose  

 

Polarity:   NEGATIVE |   PAL 

(

 

or

   NTSC    PALplus    SECAM

 ) 

9.

 

Using 

 select  line number 310 (PAL or SECAM) or 262 (NTSC) 

10.

 

Observe the trace, and check to see if the test tool triggers on line number 310 (PAL 
or SECAM, see Figure 4-14), or line number 262 (NTSC, see Figure 4-15). 

 

Figure 4-14. Trace for PAL/SECAM line 310 

Negative Video 

 

Figure 4-15. Trace for NTSC line 262 Negative 

Video 

4.6.14 Video test using SC600 Scope Calibration Option 

You can skip this test if you did  test 

4.6.13 Video test using the Video Pattern 

Generator.

 

Only one of the systems NTSC, PAL, PALplus, or SECAM has to be verified. 

Summary of Contents for ScopeMeter 19 B Series























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands