12
6 Wirin
(See Figure 6
WARNING
connection
which app
Housings w
M20 above
threads tog
personal in
certificatio
housing th
match, obt
representa
6.1 4-20
Verify polarity
The Logix 320
current source
on the user int
a voltage sour
terminals. Th
operation. Mi
The input loop
positioner shou
a ground at on
environmental
In general, shie
NOTE:
The Lo
safe barrier ra
exceed 100 m
6.2 Grou
The green gro
cap, should be
and reliable ea
tied to the sam
Additionally, th
grounded at b
WARNING
used to ter
6.3 Comp
(See figure 7.)
Output compli
can be provide
system consis
barrier resista
positioner imp
requires that t
drop across th
10.0 VDC dro
ng and Gr
.)
G:
This product
ns in either thre
ear identical bu
with M20 threa
e the conduit o
gether will dam
njury and void
ns. Conduit fit
hreads before in
tain suitable ad
ative.
mA Comm
when making
00 is reverse po
e to the input te
terface board (
rce directly acr
e current must
nimum operati
current signal t
uld be in shielde
nly one end of th
electrical noise
eld wire should
ogix 3200MD p
ating of 100 mA
mA.
nding Scre
ounding screw,
e used to provi
arth ground ref
me ground as t
he electrical co
both ends of its
G:
The green g
rminate signal
pliance Vol
)
iance voltage r
ed by the curre
sts of the curre
nce (if present
pedance. The L
the current loop
he positioner at
p across the Lo
rounding G
t has electrical
ead sizes
1
/
2
in
ut are not interc
ads are stampe
opening. Forcin
mage equipmen
hazardous loca
ttings must mat
nstallation. If t
dapters or cont
and Input W
field terminatio
olarity protecte
erminal labeled
(see Figure 6).
oss the Logix 3
always be limi
ng current is 3
to the Logix 320
ed cable. Shield
he cable to prov
e to be removed
be connected a
positioner carrie
A. Input curren
w
located inside
de the unit with
ference. This g
he electrical co
onduit should b
run.
rounding screw
shield wires.
tage
refers to the vo
ent source. A c
nt source, wirin
), and the Logi
Logix 3200MD
p system allow
t maximum loo
ogix 3200MD p
Use
Guideline
conduit
. NPT or M20
changeable.
ed with the lette
ng dissimilar
nt, cause
ation
tch equipment
hreads do not
act a Flowserv
Wiring
on connection.
ed. Wire 4-20 m
d 4-20 mA Inpu
Never connec
3200MD
ited for 4-20 mA
.6 mA.
00MD digital
ds must be tied
vide a place for
d from the cable
at the source.
es an intrinsica
ts should not
the terminatio
h an adequate
ground should
onduit.
e earth
w must not be
ltage limit that
current loop
ng resistance,
x 3200MD
digital position
s for a 10.0 VD
p current. The
positioner
er instructions –
es
ers
ve
mA
t
ct
A
to
.
ally
n
be
ner
DC
e
termina
loop cu
varies f
signal,
Figure 6
– Digital Positio
als is generated
rrent input. Th
from 9.8 to 10.0
HART commun
6: Field Termin
oner 3200MD
d by the positio
he actual voltag
0 VDC depend
nications, and
nation
LGENIM0059-
flowse
oner from the 4
ge at the termin
ding on the curr
ambient tempe
-04 09/11
erve.com
4-20 mA
nals
rent mA
erature.
