8
Figure 3: Line
5 Mou
5.1 Moun
Valve
To mount a Lo
Mark One valv
below. The fo
9
/
16
in. ope
and smalle
7
/
16
in. box
3
/
8
in. open
1. Remove w
Insert pin in
on stroke le
their corres
the unthrea
arm. Reins
follower arm
2. Slide the d
over the fla
of the posi
the custom
washer ov
the nut.
ar Mark One C
nting and
nting to Valt
es
ogix 3200MD p
ve, refer to Fig
ollowing tools a
en-end wrench
er)
x wrench
n-end wrench
washer and nut f
nto the appropr
ength. The stro
sponding holes
aded end of the
stall lock washe
m assembly.
double-D slot in
ats on the posi
itioner. Make s
mer interface si
ver the threads
Control Valve M
d Installatio
tek Linear M
positioner to a V
ure 3 and proc
are required:
(or
1
/
2
in. for sp
from follower pin
iate hole in follo
oke lengths are
in the follower a
e pin is on the st
er and tighten nu
n the follower a
tion feedback s
sure the arm is
de of the posit
on the shaft an
Use
Mounting
on
Mark One
Valtek linear
ceed as outlined
pud sizes 2.88
n assembly.
ower arm, based
stamped next to
arms. Make su
tamped side of t
ut to complete
arm assembly
shaft in the bac
s pointing towar
ioner. Slide loc
nd tighten dow
er instructions –
d
d
o
re
the
ck
rd
ck
n
3. Alig
the
4. Scre
mou
app
5. Slip
the
mou
the
6. Inse
7. Pos
clam
arm
Lea
8. Slid
stro
stro
9. Cen
follo
10. Alig
clam
– Digital Positio
gn the bracket w
positioner. Fa
ew one mountin
unting pad near
proximately
3
/
16
i
the large end o
back of the pos
unting bolt. Slid
mounting bolt a
ert the lower m
sition the take-o
mp mounting pa
m bolting and in
ave bolts loose.
e the appropria
ke length, over
ke lengths are s
nter the take-of
ower pin.
gn the take-off a
mp and tighten
oner 3200MD
with the three o
asten with ¼ in.
ng bolt into the h
rest the cylinder
in. from being fl
of the teardrop s
sitioned/bracket
de the small end
and align the low
ounting bolt an
off arm mountin
ad. Apply Loct
sert through w
.
ate pin slot of the
the follower arm
stamped by eac
ff arm on the ro
arm with the to
bolting. Torqu
LGENIM0059-
flowse
outer mounting
. bolts.
hole on the yoke
r. Stop when th
ush with mount
shaped mountin
assembly over
d of the teardrop
wer mounting ho
nd tighten the b
ng slot against
tite 222 to the t
washers into ste
e take-off arm, b
m pin. The app
ch pin slot.
olling sleeve of
op plane of the
ue to 120 in.•lb
-04 09/11
erve.com
g holes on
e
he bolt is
ting pad.
ng hole in
r the
p under
ole.
bolting.
the stem
take-off
em clamp.
based on
propriate
f the
stem
b.
