FLIGHT DESIGN CTLS Series Maintenance And Inspection Procedures Manual Download Page 28

Page: 28 / 176

Maintenance and Inspection Procedures Manual

Type:

Series:

CTLS

LSA

Page: 3-3

AF 04800001

Revision No. 3

Date: 14 Sep 2008

3.2 Run-up

Run-up shall be done prior to any inspection.
Run-up shall at least take long enough to bring all temperatures to levels acceptable for takeoff.

CT Inspection and/or Maintenance Checklist

Inspection:

1. 100hour
2. Annual

ELT battery due:
Altimeter / Transponder test due:
Systems Pre-inspection

Post-inspection

Starter

Oil pressure

psi

Brakes

Instruments & avionics

Ignition ground test
(

See Chapter 10.3.5 of the Operator’s

Manual for all versions of ROTAX 912)

Oil temperature

WARNING:

Ensure cylinder heads temperature (CHT) and oil temperature are

within limits.
Cabin heat

Oil pressure

psi

Idle RPM

RPM

WARNING:

Allow engine to cool to 300

F (CHT) before shutdown.

All exterior lights are off

Check for fuel odors in cabin

Check for fuel stains on floor

Check fuel valve

off

function

Notes:

Summary of Contents for CTLS Series

















































































































































































Search results

Summary of Contents for CTLS Series

Reviews:

Related manuals for CTLS Series

Brands by name

Popular brands

FLIGHT DESIGN CTLS Series, Maintenance And Inspection Procedures Manual

Search results

Summary of Contents for CTLS Series

Reviews:

Related manuals for CTLS Series

Brands by name

Popular brands