manualshive.com logo in svg

Flex innovations FV-31 Cypher, Instruction Manual

Share
Download
Flex innovations FV-31 Cypher Instruction Manual Download Page 36

WARNING

1.

2.

The fans on the FV-31 Cypher spin in different directions for stability and performance. Power the model and verify the motors spin in 

the proper direction as shown in the diagram below. Once confirmed, remove power from the model.

The motor numbers in this diagram correspond to the numbers used for each motor in the Betaflight or SpeedyBee Configurators.

You can also use this diagram in conjuction with the FLEXF3 diagram at the back of this manual for maintenance purposes, should you 

need to unplug one of the motors from the FLEXF3.

The front fans thread directly onto the motor shaft. In order to tighten the fans adequately, the front motors must be removed. Use a #1 

Phillips screwdriver to remove the four M3 screws that secure the motor in place.

FAN INSTALLATION

34

Please note, the right rear and front left motors have reverse direction (left hand) fan and fan adapter threads. You will need to 

tighten their corresponding nuts by turning them counter-clockwise. 

When making adjustments to the model, transmitter or FLEXF3 with the model powered, remove all fans to guard 

against accidental spool up.

FRONT

LEFT

RIGHT

Motor & Fan Direction

1

2

3

4

Summary of Contents for FV-31 Cypher



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands