manualshive.com logo in svg

Flex innovations FV-31 Cypher, Instruction Manual

Share
Download
Flex innovations FV-31 Cypher Instruction Manual Download Page 13

Connection B (with Betaflight Telemetry) Application Setup

SPEKTRUM TRANSMITTER AND RECEIVER SETUP (CONTINUED)

11

If you have chosen to utilize a Betaflight Telemetry connection (Connection B), please follow the steps below to activate 
Telemetry on the Betaflight PC application or SpeedyBee mobile application. If you have chosen Connection A (without 
Betaflight Telemetry, please proceed to the section on page 14 titled "Binding".

1. 

Betaflight Configurator

SpeedyBee Mobile App for iOS
SpeedyBee Mobile App for Android

2.

3.  

https://github.com/betaflight/betaflight-configurator/releases/

Download the Betaflight Configurator for your computer or the SpeedyBee Application for your mobile device. You can 
search for these applications online (or in your mobile device's app store) or visit the web addresses shown below. 

Computer

Connect the FLEXF3 controller to the computer via the provided USB cable. You do not need to power the aircraft with 
your flight battery. 

Mobile Device

Connect the provided bluetooth module to the FLEXF3 controller. You will then need to power the aircraft in order to 
provide power to the bluetooth module. You do not need to pair the device in your mobile device settings menu.

Open the application. Click "Connect" in the upper right hand corner to connect to the FLEXF3 controller.

Search for "SpeedyBee" in your device's application store

Summary of Contents for FV-31 Cypher



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands