manualshive.com logo in svg

Flex innovations FV-31 Cypher, Instruction Manual

Share
Download
Flex innovations FV-31 Cypher Instruction Manual Download Page 31

1.

2. 

Power on your transmitter and the Cypher being sure you have control. Place your FLEXF3 Profile switch (Channel 5) into the 

Advanced Profile position. You can confirm that it is in the correct position by rotating the aircraft to a specific angle away from level. If 

the aircraft only attemps to correct while it is in motion, you are in the correct profile. If it attempts to correct the angle even after motion 

has stopped, you are in the incorrect profile.

Place the elevon gauge over the top surface of the wing, parallel to the wing root. Slide the silicone keeper on the clevis away from the 

control horn, then use a flat bladed screwdriver to open the clevis and remove it from the control horn. Turn the clevis in or out as 

needed to align the elevon with the elevon gauge. Snap the clevis closed over the control horn and return the silicone keeper to the end 

of the clevis near the control horn. Note that the elevon may appear to be slightly angled up relative to the wing when properly centered. 

ELEVON SETUP

29

Required Tools and Fasteners:

Elevon Centering Gauge

Flat Blade Screwdriver

Summary of Contents for FV-31 Cypher



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands