manualshive.com logo in svg

Flex innovations FV-31 Cypher, Instruction Manual

Share
Download
Flex innovations FV-31 Cypher Instruction Manual Download Page 18

Application Setup

FUTABA TRANSMITTER AND RECEIVER SETUP (CONTINUED)

16

If you you are using a Futaba S.BUS connection, please follow the steps below to complete setup on the Betaflight PC 
application or SpeedyBee mobile application.

1. 

Betaflight Configurator

Speedy Bee Mobile App for iOS
Speedy Bee Mobile App for Android

2.

3.  

https://github.com/betaflight/betaflight-configurator/releases/

Download the Betaflight Configurator for your computer or the SpeedyBee Application for your mobile device. You can 
search for these applications online (or in your mobile device's app store) or visit the web addresses shown below. 

Computer

Connect the FLEXF3 controller to the computer via the provided USB cable. You do not need to power the aircraft with 
your flight battery. 

Mobile Device

Connect the provided bluetooth module to the FLEXF3 controller. You will then need to power the aircraft in order to 
provide power to the bluetooth module. You do not need to pair the device in your mobile device settings menu.

Open the application. Click "Connect" in the upper right hand corner to connect to the FLEXF3 controller.

Search for "SpeedyBee" in your mobile device's application store.

Summary of Contents for FV-31 Cypher



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands