manualshive.com logo in svg

Flex innovations FV-31 Cypher, Instruction Manual

Share
Download
Flex innovations FV-31 Cypher Instruction Manual Download Page 28

VERTICAL FIN INSTALLATION

26

Required Tools and Fasteners:

Medium CA                               Medium Grit Sandpaper

#1 Phillips Screwdriver

1.

2.

Locate the two vertical fins as well as the rear hatch removed when setting the rear fan tilt. Test fit the vertical fins into the rear hatch, 

noting that they only fit in one direction and on a particular side (the FV-31 Cypher logos should face out). If your Cypher has painted 

mating surfaces, scuff them with a medium grit sandpaper to remove paint and promote adhesion. Use medium CA to secure the fins in 

place.

Once the vertical fins have dried, use a #1 Phillips screwdriver and the screws removed in the tilt setup section to secure the rear hatch 

assembly onto the fuselage. Note that the two shorter screws are used for the rear mount locations, and the longer screws are used for

the front mount locations.

*fins shown removed for clarity

Summary of Contents for FV-31 Cypher



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands