background image

5

LED INDICATORS

The YZ300 (YZ320) contains 6 LED's that provide information that can be useful in determining the
current state of the interlocks wired between terminals L1 and P of the BurnerLogix control.

Table 2:

YZ300 (YZ320) DEFAULT MESSAGES

STATUS

 – indicates red  when the ED580 co nnection  to th e 

 Bu rnerLogix is interrupted, green when connection is establish ed. 

RECYCLING

 – illuminates steady when  all interlo cks 

 between termin al L1 and 3 are clo sed and powered.  
Blin ks if an y interlock is open. 

WATER

 – illuminates steady when Low Water an d High  

Water are closed  an d powered, blinks  if any  is  open. 

OIL

 – illu minates stead y if all oil interlo cks between 

 terminals 44 and 55 are closed and po wered an d oil is  
an  active fuel, blinks if an y oil in terlock is open. 

GAS

 –  illuminates  steady if  all  gas  interlocks  between   

terminals 50  and 5 4 are clo sed and powered and  gas  is 
 an active fuel, b links if any gas interlock is open. 

NON-RECYCLING

 - illuminates steady when all 

 in terlocks between terminals 54 and  P are closed 
 and powered, blinks if an y interlock is o pen. 

OIL MODE 

GAS  MODE 

Terminal Messa ge  Terminal Message 

Recyc ling Limi ts 

L1-40 

Op Control Open 

L1-40 

Op Control Open 

40-41 

L1-3 Aux#1 Open 

40-41 

L1-3 Aux#1 O pen 

41-42 

L1-3 Aux#2 Open 

41-42 

L1-3 Aux#2 O pen 

42-3 

L1-3 Aux#3 Open 

42-3 

L1-3 Aux#3 O pen 

Non-Recycl ing Limi ts 

3-43 High 

Water 

3-43  High 

Water 

43-44 Low 

Water 

43-44  Low 

Water 

For OIL select, conn ect termi nal 49 to 53 

For GAS  select, conn ect termi nal 45 to 49 

45-46 

High Oi l Temperature 

50-51 

Low Gas Pressure 

46-47 

Low O il Temperature 

51-52 

High Gas Pressure 

47-48 

Low O il  Pressure 

52-53 

Aux G as 

48-49 

Low Atomizing Media 

 

54-55 High 

P re ssure 

54-55  High 

Pressure 

55-56 High 

Temperat ure 

55-56  High 

Temperature 

56-57 

Aux #4 O pen  

56-57 

Aux #4 Open  

57-58 

Aux #5 O pen  

57-58 

Aux #5 Open  

58-59 

Aux #6 O pen  

58-59 

Aux #6 Open  

59-60 

Aux #7 O pen  

59-60 

Aux #7 Open  

60-P 

Air Flow Open 

60-P 

Air Flow Open 

Summary of Contents for YZ300















Reviews: