®
9
3. TECHNICAL DATA
Power supply voltage; current:
230/110(115) VAC (50/60 Hz); 0.5/1.2 A (230/110 VAC)
Ignition HT transformers: input, output, weight, dimensions:
–
P/N
TX-230-8000
input: 230 VAC at 0.5A; output: 8000 VAC, 15 mA, 100% duty cycle
–
P/N
TX-110-8000
input: 110/115 VAC at 1.2A; output: 8000 VAC, 15 mA, 100% duty cycle
weight, dimensions:
1.8 kg, LxWxD 107x87x64
Method of operation:
electrical arc
Ignition control signal:
24 VDC, max. 12A (20A peak)
Available rod insertion length L1:
0.65 ÷ 3.15 m
Rods and tips outer diameter, material: Ø16 mm, 316 SS
Rods optimal electrical operation parameters:
15-20 mA at 7,500–10,000 V
Rods and tips: operating temperature, IP rating, weight:
–
P/N
HTSS-xxx-J
-40°C ÷ +100°C, IP67 (j. box), +200°C rod tube;
L1=0.65 m - 0.77 kg
–
P/N
HTSS-xxx-CEX
-40°C ÷ +80°C, IP66 (cable entry), +200°C rod tube; L1=0.65 m - 1.00 kg
–
P/N
HTSS-xxx-J-CEX
-40°C ÷ +80°C, IP66 (j. box), +200°C rod tube;
L1=0.65 m - 1.73 kg
rods weight adder:
approx. 0.44 kg / meter
–
Tip P/N
HTR-TIP
length 160 mm, 0.16 kg;
caution:
used on rods lengths L=0.5, 0.6, 0.7 only
–
Tip P/N
HTR-TIP-L
length 460 mm, 0.32 kg
tip operating temperature:
+300°C tip continuously, over +1,000°C in flame for short period central
Kanthal electrode over +1,000°C continuously
Power packs: operating temperature, IP rating, weight, material:
–
P/N
HTSS-PP-230/110
-40°C ÷ +65°C, IP66, 6 kg; C. Steel powder-coated or option S. Steel
–
P/N
HTSS-PP-230/110-CEX
-40°C ÷ +65°C, IP66, 20 kg; Cast Alum. powder-coated or option S. Steel
HV ignition single wire cable data:
–
P/N
HT-CAB-5
:
type FZ-LSi, OD 7 mm, 15kV, wire 1.0 mm², oper. temp.: -50 +180°C
–
P/N
HT-CAB -5-CEX
: type FZ-LSIekw, shielded, OD 8 mm, 15kV, wire 1.0 mm², oper. temp.: -50 +180°C
–
P/N
HT-CAB-5
and
HT-CAB-5-CEX (5 m working length)
weight: 0.37 kg and 0.42 kg
Notice: The recommended length of the ignition cable is 5 m. The 10 m long cable is also offered but its use
will decrease the arc energy, which should be remembered. For that reason one should not use a longer cable.
Flame monitoring (in case of S&S mode used): MBCE-110/230FR flame rod module:
–
operation mode: continuous
–
functional safety: suitable for installations up to and including
SIL2
(Exida’s FMEDA report)
Notes:
1. If the above parameters are different than those required please contact Fireye
2
. For Imperial Units please refer to the Appendix 2 Unit Conversion Table
3
. Device
complies with the requirements of the European Directive 2011/65/EU (RoHS 2)
MARKING:
The
HTSS
igniter was independently tested and evaluated by the EMC Accredited Laboratory.
Assessment of compliance of the device with the essential requirements of the European directive no. 2014/30/EU
was carried out. Declaration of Conformity was issued and igniter was CE marked accordingly.
4. HAZARDOUS ZONE ATEX CERTIFIED SUBASSEMBLIES:
4.1 Igniter rods type
HTSS-xxx-CEX
and
HTSS-xxx-J-CEX
:
ATEX Certificate, marking: II-/2G Ex d IIC T4 Gb, II -/2D Ex t IIIC 135ºC Db
4.2 Power pack P/N
HTSS-PP-xxx-CEX
enclosure type GUB4, IP66:
a) ATEX Certificate, marking: Ex II 2G Exdb IIC T4-T6; Ex II 2D Ex tb
IIIC T85°C, T100°C, T135°C
b) IECEx Certificate, marking: Ex db IIC T6, T5, T4; Ex tb IIIC T85°C, T100°C, T135°C