background image

P

AGE 

18

I

NSTALLATION 

( C

ONTINUED

)

Finalizing the Installation

!

     

ACID WASH WARNING

      :    Before installing the faceplate, make sure any masonry that has been

treated with acid wash has been properly neutralized (this is used primarily with brick faces).  Acid
wash (muriatic acid) is used to remove excess mortar.  If not properly neutralized with an ammonia
solution, the gold face may develop a permanent tarnish when the acid evaporates over time.

!

     

WOOD SCRAP WARNING

       

:     Never burn wood scraps in the fireplace.  Treated wood breaks down

the catalyst inside the fireplace, decreasing efficiency and increasing emissions.

1

Remove the set-up face using a phillips screwdriver included with the faceplate.

Use a phillips screwdriver to remove 
the 10 screws holding the set-up 
face in place.

Phillips 
Screwdriver

2

Make sure the firebrick is properly in place.

3

Install the log retainer using the included 1/8" allen wrench.

4

Install the baffle, grate, and log retainer.

AAAAAAAAAAAAAA

AAAAAAAAAAAAAA

AAAAAAAAAAAAAA

AAAAAAAAAAAAAA

AAAAAAAAAAAAAA

AAAAAAAAAAAAAA

AAAAAAAAAAAAAA

AAAAAAAAAAAAAA

AAAAAAAA

AAAAAAAA

AAAAAAAA

AAAAAAAA

AAAAAAAA

AAA

AAA

AAA

AAA

AAA

AAA

AA

AA

AA

AA

AA

AAA

AAA

AAA

AAA

AAA

AAA

AA

AA

AA

AA

AA

Place the grate in the center 
of the firebox.

Place the baffle on the brackets at 
the rear of the firebox (the bend 
goes upwards).

1/8" Allen

Place the log retainer into the 
holders.  Tighten down the set 
screws in the holder with the 
included 1/2" allen wrench.

Make sure the side and rear 
firebrick is against the wall.

Summary of Contents for 36 ELITE-ZC

























Reviews: