manualshive.com logo in svg

Fire-Lite DACT-UD, Manual, Page: 40 / 60

Share
Download
Fire-Lite DACT-UD Manual Download Page 40

Programming for DACT-UD

Simultaneous Data Transfers

40

DACT-UD  PN 51899:B1    1/25/05

Once an incoming call is accepted/answered by the control panel, the panel will

1. Establish basic modem connection

2. Verify secret code

3. Verify callback vs. no callback request from the Service Terminal.  If callback is 

requested then perform steps 4 through 10.  If no callback is requested then 
perform steps 9 and 10 only

4. Identify the Service Terminal location

5. Hang-up/disconnect call

6. Call the Central Station(s) and transmit a request for upload/download message 

(if programmed to do so).  If this message is accepted, the control panel will 
proceed to the next step

7. Return call to Service Terminal

8. Verify secret code

9. Begin uploading

10. Upon completion of upload, call Central Station(s) back and report a successful 

upload or failed upload/download status (if programmed to do so)

During the uploading process, the fire protection remains active.  Should a system 
trouble or alarm condition occur, the control panel immediately terminates uploading 
and processes the trouble or alarm locally and transmits the information to the Central 
Station(s).

3.5  Simultaneous Data Transfers

Uploading and downloading may take place on a single telephone call.  Control and 
selection of the data transaction is coordinated at the Service Terminal.  This eliminates 
multiple phone calls, allows instant verification of downloaded data files and simplifies 
the overall process.

Summary of Contents for DACT-UD





























































Reviews:

No comments