manualshive.com logo in svg

Fire-Lite DACT-UD, Manual, Page: 17 / 60

Share
Download
Fire-Lite DACT-UD Manual Download Page 17

Programming the MS-9600 Fire Alarm Control Panel

Programming for DACT-UD

DACT-UD  PN 51899:B1    1/25/05

17

SECTION 3

Programming for DACT-UD

3.1  Programming the MS-9600 Fire Alarm Control Panel

Refer to the MS-9600 Manual programming section for general programming 
information.  To program the MS-9600 FACP for use with the DACT-UD:

1. Press the 

Enter

 or 

Mode

 key to display the Read Status/Programming screen

2. Press 

2

 to access Programming

3. Enter the Master level password

4. Press the down arrow key twice to view the screen with the Option Modules 

choice

5. Press 

3 

for Option Modules to access the Option Modules screen as shown to the 

left

6. Program the FACP for use with the DACT-UD using the following procedure

3.1.1  On-Board DACT 

The DACT-UD (Digital Alarm Communicator/Transmitter) is an optional module 
which installs directly on the FACP main circuit board for communication to a 
central station.  Pressing 

2

 while viewing the Option Module Screen will cause the 

following screens to be displayed:   

3.1.1.1  DACT-UD Enable

To enable the on-board DACT module, press 

1

 while viewing On Board DACT 

Screen #1 until the display reads 

Enabled Yes

.  The display will toggle between 

Enabled Yes

 and 

Enabled No

 with each press of the key.

   OPTION MODULES
1=ANNUNCIATORS/UDACT
2=ON BOARD DACT
3=PRINTER/PC

Option Module Screen

    ON BOARD DACT
1=ENABLED        YES
2=PRIMARY PHONE
3=SECONDARY PHONE

On Board DACT Screen #1  

    ON BOARD DACT
1=SERVICE TERMINAL
2=CENTRAL STATION
3=MANUAL DIAL MODE

On Board DACT Screen #2  

Summary of Contents for DACT-UD





























































Reviews:

No comments