manualshive.com logo in svg

Fire-Lite DACT-UD, Manual, Page: 15 / 60

Share
Download
Fire-Lite DACT-UD Manual Download Page 15

Installation in MS-9600 FACP

DACT-UD Installation

DACT-UD  PN 51899:B1    1/25/05

15

3. Insert the supplied plastic snap-in standoff into mounting hole located at the 

bottom center of the DACT-UD module (insert into back of board)

4. Carefully plug connector J1 on the back of the DACT-UD module into connector 

J2 on the MS-9600 main circuit board, being careful not to bend any pins and at 
the same time, insert plastic snap-in standoff into mounting hole in main board

5. Align the mounting holes in the DACT module with the premounted standoffs on 

the FACP main circuit board 

6. Secure the module to the standoffs on the main circuit board with the three 

screws supplied with the DACT-UD.  It is important that the supplied screws be 
used to secure the module to the metal standoff in order to help protect against 
electrical transients.  

7. Reinstall the Keypad/Display on the main circuit board by positioning the unit 

over the appropriate standoffs and securing with the screws which were loosened 
in step 2

8. Make certain to program the control panel for DACT operation

Figure 2.3 DACT J1 Connector to FACP J2 Connector

J1

J2

Standoff

Standoff

Standoff (snap-in)

J1 Connector located on 
back of DACT module

96dac

t2.C

DR

Standoff

Figure 2.4 DACT Installation on Standoffs

Mounting Screw

Mounting Screws

96dac

t3.CDR

Snap-in Standoff

Summary of Contents for DACT-UD





























































Reviews:

No comments