manualshive.com logo in svg

fimotec-fischer 90.0210.61, Operating Instructions Manual

Share
Download
fimotec-fischer 90.0210.61 Operating Instructions Manual Download Page 45

Operating instructions FS-26E 

 

 

 
 

 

Status as of 10 / 2019 

Page 47

 
 

 

8      Maintenance and cleaning 

The control device works maintenance-free. 
The safety inspection in acc. with DIN VDE 0701-0702 is to be performed annually. 
 
Pull out the mains plug before cleaning the housing of the device with liquids.  
 
 

9     Disposal 

The control device must not be disposed of in the normal household waste. 
 
Users are obligated to drop off old devices at a disposal point for old electrical and electronic 
devices. The separate collection and proper disposal of your old devices helps to conserve natural 
resources and ensures recycling, which protects human health and the environment. Information about 
where you can find disposal points for your old devices can be obtained from your city administration or 
local waste disposal facility.  
 
 

10  

 

CE  conformity 

The control device FS26E is marked with the CE marking and therefore meets the relevant European 
directives. 
The company fimotec-fischer GmbH & Co. KG herewith confirms that this device meets the following 
directives: 

  Low-voltage directive 2014/35/EU 

  EMC directive 2014/30/EU 

  Standards EN 61000-6-4 and EN 61000-6-2  

The declaration of conformity is archived at the manufacturer. 
 
 

11  

 

Service 

If you have any questions or problems, please contact the supplier directly. 
Manufacturer hotline for fimotec-fischer GmbH & Co.KG:   

Tel.: 0049-7424-884-0 

 

   Note 

Please keep the following information ready, since otherwise service cannot be provided: 
-  Your company with address 
-  Your name and contact data, such as telephone number and e-mail address 
-  Complete designation of the device 
-  Serial number (FBxx-xxxx-xx or HW20xxxx) 
-  The direct supplier of your device or machine in which the device is integrated. 
 

11.1   Operator codes 

The following codes are available: 
Without 

code    Operator 

 

System operator (code A) 

  System setter (code B) 

 
It is up to the system supplier to pass on the operator codes or to reserve them for his service personnel. 
Via the system setter operator code, parameters are enabled which may only be changed by skilled, 
trained personnel, since the function and limit values of the conveyor devices are influenced with these 
settings. 

Summary of Contents for 90.0210.61















































Reviews:

No comments

Brands by name

Popular brands

Load more brands